Question about 1999 GMC Jimmy

1 Answer

How to replace abs sensor 1995 jimmy - 1999 GMC Jimmy

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 299 Answers

I think it is integral to the wheel bearing assembly

Posted on Sep 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My abs light comes on and off brakes are good 1998 gmc jimmy


ABS computer is receiving erroneous signals into the ABS computer. Wiring loom connections need checking. Disconnect, reconnect wiring looms around engine compartment dealing with abs equipment. Spray contact with contact cleaner.

Feb 11, 2015 | 1998 GMC Jimmy

1 Answer

ABS Problem in my 2000 Jimmy 4x4


the best way to diagnose this problem would be with a scan tool while driving and watching the speed sensors, or check all your wheel tone rings make sure there are no cracks and they are clean, also have the computer scaned for abs codes there should be a code that may tell you which wheel speed sensor is acting up,you can also check the wiring, these seem to chaf the wiring by the control arm .a bad wheel bearing may also cause this problem, i would start with a scan of the abs system,good luck.

Feb 22, 2010 | 2000 GMC Jimmy

1 Answer

My 1995 jimmy shuts of with a check eng light on starts back up after 30 sec my brakes and abs also come on at the same time


Check the charging system,it needs to be 13.65 volts to14.25 volts output at the battery,with the ac/heat on high blower,and the headlights on,if it is lower than tis,then the alternator needs replacing.

Jan 30, 2010 | 1995 GMC Jimmy

1 Answer

ABS Code 67


no check all 4 wheels for the metal rings fitted to drive shafts that have little squares on then this is what the sensoirs read from ,make sure that one of them hasnt come loose and it spinning around ,if loose spot weld it to the shaft

Dec 13, 2009 | 1995 GMC Jimmy

1 Answer

I have a 1997 gmc jimmy. the abs unit locks up between 7mph and 5mph and the brakes stop working.


There was a recall on the ABS system on your truck. The problem was the ABS sensor on the front wheels were getting dirty and corroded causing a faults signal to the ABS module. The fix was to inspect the ABS sensor and clean them with brake parts cleaner and re-gap the sensor to the speed ring on the hub. The ABS sensor and speed ring is on the inside of the front wheel hub, spry brake parts cleaner and re-gap the sensor to the speed ring with paper folded 5 times. I feeler gauge will work but put a paper between the sensor and gauge cause the sensor is magnetic and the gauge will stick. Look for damages to the lead wire to the abs, but i think that's all fine since you did not mentioned any abs light on. You may be even lucky with just a good spray of the brake parts cleaner. Good luck and keep me posted.

Nov 04, 2009 | 1997 GMC Jimmy

1 Answer

Sensor problem with 1999 gmc jimmy


check the sensors at the wheels.

May 27, 2009 | 1999 GMC Jimmy

1 Answer

I have a 1995 GMC Jimmy, ABS never shuts off???


its an abs problem code,the only check u can do without having it scanned,is to in spect wires for damages behind frt wheels going to sensors

Mar 10, 2009 | 1995 GMC Jimmy

1 Answer

2001 GMC Jimmy


i believe you have 2 seperate issues. the abs/brake lite issue i would suspect a front speed sensor, i have replaced many. does the vehicle have an odd stopping feeling just as you come to a stop? the second part could be an issue with fuel quality(who knows these days!) seems coincidental it happened right after filling, other than tune-up parts, other suspects are mass air flow sensors, coolant temp switches, even 02 sensors, is engine lite on? maybe have it scanned to be sure nothing is stored in computer. (autozone will scan for free)

Oct 16, 2008 | 1995 GMC Jimmy

2 Answers

Dash lights on abs and brake


this is a abs pump problem. common on these circuits get "unsoldered" from vibration. if you feel like you can solder conections its a good couple hour job and sometimes things get burned out from voltage spikes. good luck jimmy rate as fixya thanx

Sep 25, 2008 | 2001 GMC Jimmy

1 Answer

Camshaft Sensor - How do you replace it?


The O2 Sensor is on the drivers side by the cadilatic converter.

Jul 12, 2008 | 1995 GMC Jimmy

Not finding what you are looking for?
1999 GMC Jimmy Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...