Question about 2001 Ford Focus

1 Answer

Engine light has came on, exust is spluttering a bit and power is affected. my exust heatshield wasloose a few days ago and i caught it on a speed bump. can anyone help?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,341 Answers

You need to have a computerised diagnostic in order to get an error code from the vehicle.Once you get that then you will know where the fault is.This should solve, but remember it may be quite difficult to find the fault sometimes and think twice before you change any parts.

Posted on Sep 27, 2009

Testimonial: "thank you very much, i suspect i may have to. i was trying to locate just where my exhaust sensor is located. if it is on the underside near the exhau"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The car starts perfect,some days runs a few miles,cuts out,all lights on,turn off restarts perfect,might run a few days or a few miles,then same again.no codes come up or in memory;when i ask for big


Sounds like an electrical issue. Could be a bad relay (fuel pump, ignition, ASD). These can be a bear to diagnose, but the good? news is it will get worse and then be easier to find. If you could hook up a GOOD scan tool and have a helper with you for days at a time (I know, ain't gonna happen) to watch the real time data you might see what it happening when it fails. I have even seen a bad gas cap do this!

Mar 23, 2016 | Cars & Trucks

3 Answers

My diesel vw transporter misfires/splutters on


Hi there,
I have just had my T4 2.4 cambelt and water pump done but the van does not run right unless the choke is out any ideas?
Many thanks
Mark

Mar 31, 2010 | 1999 Volkswagen Euro

1 Answer

Check engine light coming on off and on, seems to


The harmoic balancer is located on the end of the crankshaft. This shaft is the largest shft in the engine and should be the one where all belts eventually run thru/over it. Check it out, let me know.
1ledsled1@comcast.net

Jan 17, 2010 | 1987 Subaru Gl 4WD

1 Answer

My 2005 Nissan Altima loss power while I was driving down the street, the next day it cut off at a light, it takes a few seconds to start, but always starts


the 2.5 altima's had a recall on that problem about 2-3 years ago. Go to edmunds or progressive find the recall letter and the dealer will fix it free. well here you go:

section_opened.gif Recall ID # 07V527000 - ENGINE AND ENGINE COOLING Recall Date: NOV 14, 2007 Component: ENGINE AND ENGINE COOLING Model Affected: ALTIMA Potential Units Affected: 653910 Recall Details Recall Date: NOV 14, 2007

Model Affected: 2005 NISSAN ALTIMA

Summary: ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT POSITION SENSOR CAN OVERHEAT CAUSING A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.

Consequence: IF THE INTERRUPTION IN THE SIGNAL FROM THE CRANKSHAFT POSITION SENSOR IS SO BRIEF THAT THE ELECTRONIC CONTROL MODULE (ECM) LOGIC DOES NOT HAVE TIME TO DIAGNOSE THE CONDITION, THE ENGINE MAY STOP RUNNING WITHOUT WARNING WHILE THE VEHICLE IS DRIVEN AT A LOW SPEED INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPROGRAM THE ECM FREE OF CHARGE. CERTAIN MY 2006 ALTIMAS WHICH HAVE BEEN PREVIOUSLY REMEDIED UNDER RECALL CAMPAIGN 06V223 (NISSAN R0606) ARE NOT INCLUDED IN THIS RECALL SINCE THE REPROGRAMMING FOR 06V223 ALSO INCLUDED THIS REPROGRAMMING. THE RECALL BEGAN ON DECEMBER 31, 2007. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.

Potential Units Affected: 653910

Notes: NISSAN NORTH AMERICA, INC.

Jun 15, 2009 | 2005 Nissan Altima

1 Answer

I have a 1998 ram 1500 4x2 it showing a 0500 code, speed sensor.


Yes I had the same problem and it was the sensor on the rear axle.

Jun 03, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
2001 Ford Focus Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...