Question about 2008 Jeep Liberty

1 Answer

Where we pull the door closed (Interior) our rings have scratched the surface up. How to fix or replace it?

Posted by on

  • myock Sep 27, 2009

    This area is ruff in texture,and resists armoral or scratch remover products.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Armoral

Posted on Sep 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do I fix my door ajar light stays illuminated


its a bad door ajar switch. which one? you would need a scan tool. but the drivers door does get used more.....

Sep 26, 2014 | 2004 Ford F150

2 Answers

The interior lights in my 2004 VW jetta do not turn on when the driver door is opened.


If I am remembering correctly, the switch is part of the latch. Each door has its own switch to turn on the interior light, and it sounds like the switch in the driver's door latch is either stuck or junk. If it has to be replaced it is very simple to remove for those that know how, but a nightmare for those that don't. The exterior handle has to be removed to release the pull-cord to the latch, interior trim panel and vapor barrier has to come off. Electrical harness, lock rod, interior handle rod, all have to be removed. Now the latch. Then it all has to go back together, and most importantly, it all has to work. I'm not saying it's not possible. I'm saying that it can ruin your day and your wallet if something goes wrong.

Jan 09, 2014 | Cars & Trucks

1 Answer

1999 Isuzu Trooper door won't open


those door latches use a very tense spring that engage the closing mechansim. If the handle lifts without any restiction at all,,the sping is missing...if the handle when pulled or lifted offers slight resistance,this means it is very weak and needs replaced. it does not have enough rigidity to release the lock works from the lock pin that is fixed to the inside door facing.

Jun 07, 2012 | 1999 Isuzu Trooper

1 Answer

My problem is. when i turn my headlights on i get this constant ringing for at least three or four minutes... my car is a 2001 volkswagen jetta tdi.


The drivers door switch turns on/off the interior lamp BUT it is also used to signal the door open and closed position. So it is not getting a door closed signal either from the door proximity switch or I believe on VW a switch on the locks interior ! Therefore it thinks you have left your H/lights on and exited the vehicle ! Hope this get's you back on the road

Apr 11, 2010 | 2001 Volkswagen Jetta TDI

1 Answer

How do i replace the headlight bulb on a f-150


Headlight bulb - replacement
Warning: Halogen gas filled bulbs are under pressure and my shatter if the surface is scratched or bulb is dropped. Wear eye protection, gloves, and do not touch surface of the bulb with your fingers because oil from your skin could cause it to overheat and fail prematurely, If you do touch the bulb surface clean it with rubbing alcohol. Try to handle bulb grasping only the base whenever is possible.
1. Remove headlight bulb cover from the back of the headlight housing on which side you replacing bulb.
2. Disconect the electrical connector from the bulb holder.
3. Rotate the headlight bulb retaining ring counterclokwise as wieved from the rear.
4. Withdraw the bulb and the retaining ring from the headlight housing.
5. Remove the bulb from the socket.
6. Without touching the glass with your bare fingers, insert the new bulb into the socket and then into the headlight housing. Install and tighten the retaining ring by turning it clockwise.
7. Plug in the electrical connector, test the headlight operation, then close the hood.

Feb 19, 2010 | 2009 Ford F-150

1 Answer

My alarm activates and interior light comes on when door is


Replace the drivers door switch, it's shorting out. It's on the B-pillar below your door latch, covered in rubber that you can pull off to get access to it. You can take it out, just tie a string to the electrical connector and tape it to the door so you don't loose it. The switches are fairly cheap at the dealership.

Nov 22, 2009 | 2004 Hyundai Elantra

2 Answers

The ignition bell wont stop ringing


You need to unplug the door harness one at a time to locate which door is causing the problem. Once the door is located, you can replace the switch which is located on the lock mechanism.

Sep 29, 2009 | 1994 Ford Ranger Supercab

1 Answer

Door sensor


Will pushing on the door-closed switch turn off the alarm? If it does, extend the button with something glued on to it so that the door will operate the switch. If the switch is damaged, it will need to be replaced.

Sep 11, 2009 | 2000 Chrysler Cirrus

1 Answer

Interior trim panel removal instruction


Normal 0 . Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.


If you don't have power windows you will have to remove the manual window crank. It is held in place by a clip on the back side of the base. To remove the clip, you will need a small hook (kind of like a knitting needle). Put the hook in behind the base, and grab the clip and pull it off. To replace it, slide the clip back on the window crank, and snap it back on the door.

May 31, 2009 | 2003 Volkswagen Passat

1 Answer

Driver side interior door handle stuck open (not flush with door)


the only way to fix handle is to replace it.not to difficult.

Mar 17, 2009 | 1999 Lexus ES 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...