Question about 2006 Subaru Legacy

Open Question

How do i remove the rear door skins in a 2006 subaru liberty? seems like there is something holding it on after iv pulled out all the clips around the edge. and no screws that i can find, but be happy to be corrected

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Rebgagnon
  • 382 Answers

SOURCE: Need to replace a headlight assembly for a 2006 Subaru Outback.

No, you just remove the radiator grill and the side marker light and the headlight housing bolts and it comes out. Not a real hard job and is Real straight forward. Good luck and have a good day.

Posted on Mar 29, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove rear bumper 2010 liberty wagon


RTM?
pulls skins
unbolt it?
05 liberty, called KJ

fsm quote
skins are facia
1.BODY/EXTERIOR/REAR WHEEL OPENING
FLARE MOLDINGS - REMOVAL)
(2) Remove the rear lamp units. (Refer to 8 -
ELECTRICAL/LAMPS/LIGHTING - EXTERIOR/
REAR LAMP UNIT - REMOVAL)
(3) Remove the four side bolts. (Fig. 2)
(4) Remove the two bottom rivets.
(5) Remove the 3 screws along the upper edge.
(6) Separate the side plastic retainers and remove
the fascia from the vehicle.

once this is off, all else is obvious. steel parts. damaged
you never state why or if damage was present so....


Mar 10, 2015 | 2010 Jeep Liberty

1 Answer

Removing rear door panel 2004 subaru outback


Remove the trim ring around the inside door handle by pulling it up and towards you first, then downwards.
Remove the switch panel. There are two spring clips holding it. Lever up carefully on the top end edge first, then push the panel towards the car floor. Disconnect the electrical connector.
Remove the screws behind the door handle, under the switch panel mount, and on the armrest.
Dislodge the 7 trim clips around the edge of the door trim, starting at the lower edge and working up. Lift the door trim out of the top channel.
If you remove the plastic sheet, take care not to tear it, a spatula is handy for this.

Apr 15, 2012 | Subaru Outback Cars & Trucks

1 Answer

How do I change rear wiper motor?


Step 1: Remove wiper arm.

Pull back the little plastic cover to gain access to the retaining nut. Loosen the nut until the threads are flush with the nut, and while pulling on the wiper arm give the nut a couple light taps with a hammer. Once the arm moves remove the nut and the arm.

Step 2: Remove the plastic door trim.

Remove the two screws holding the lift gate "easy reach strap". Carefully pry the plastic skin and pop the clips out. I started at the latch and worked out. Once all of the clips are loose sit the rear of the truck and pull the door toward you. The plastic slides over a bulge where the rear windows handle and door meet. Lift up and pull out here on the plastic and the whole thing should come off.

Step 3: Remove the weather barrier.

Carefully peel back the weather barrier making sure not to rip it. You'll only need to pull it back about 1/2 way to access the motor. I went right to left.

Step 4: Unplug the motor.

There is a single clip plug. Just unplug it.

Step 5: Remove the motor in its mount.

Remove 3 bolts holding the motor mount to the door. They are brass colored and mount to rubber flanges.

Step 6: Remove the motor from the mount.

There are 2 bolts holding the motor to the mount. Remove them and you now have the bad motor completely out. Take it to the parts store so you can save yourself a trip getting the core charge back.

Step 7: Re-assemble.

Just work backwards from step 6. The weather barrier should go back on without any problem, but if it lost its stick you could use rubber cement to reattach it. When you reinstall the plastic skin start with the part that has to go over the "handle bulge". Then just line it up and tap it back into the clips.


Apr 04, 2012 | 1998 Ford Expedition

1 Answer

Changing door skin for front passenger side door for Honda Pilot 2006


The skin is only spot welded in a few spots other then that is just a sealer all around the skin holding it and protecting it at the seam.
Remove the door and inner panel.
Drilled out the few spot welds.
Wire wheeled the exposed sealer around skin on the inside door jamb.
Use scraper to slowly work the folded edge up 90 degrees.(anything slim and small would work)
(With the old one you could just grind the edge off.)
Carefully pulled skin off.
Few minutes of dolly and hammering around the now new door skin lip to create a perfect 90 degree shape all around with the edge just peeled up.
Apply sealant to new door shell edge.
Slide skin on and in exact location needed.
Clamp skin all the way around.
Remove a few clams on one side, start hammer and dolling extra lip back around the shell lip, when done put clamps back on, and keep going down the line in this order.
Let clams sit as long as the sealer you have used suggests.
Reinstall door. Read more at http://www.honda-tech.com/showthread.php?t=2474146&ktrack=kcplink

Dec 04, 2010 | 2006 Honda Pilot

2 Answers

The drivers side door won't open from the outside. How do you take the door apart from the inside? Thanks!


There are a couple of screws holding the armrest in place, remove them. Using a small pick type of tool, pop out the power window master switch, there is another screw under it. The door panel itself is held in place with push clips, so grab the panel from the bottom and pull it out until all the clips are out of the door, then slide it straight up to get it off the top of the door edge.

Nov 22, 2009 | 1993 Buick LeSabre

2 Answers

How do you replace a Drivers side headlight bulb 2006 kia spectra


Helps to remove the battery, but small ahbds can do it.

Directly behind the lens is a big round cap ... twist it off. The bulb is held in place with a spring that locks in to a notch in the holder. When handling the new bulb, don't touch the glass. The oil from your skin will cause it to shatter when turned on.

Oct 15, 2009 | 2006 Kia Spectra

1 Answer

How do i get the inside cover off the rear drivers side door on a 2005 liberty


couple of things to look for, if its manual window, there will be a clip (sometimes) on the lever that holds it onto the door. also, there can be screws holding on the door handles onto the door, check for them. also, most have snap clips that hold the panel onto the door, remove GENTLY they are a pain in the *** to fix if they break off and you have to put new ones back on the pannel.

hope that helps

Sep 27, 2009 | 2005 Subaru Legacy

1 Answer

Need to replace a headlight assembly for a 2006 Subaru Outback.


No, you just remove the radiator grill and the side marker light and the headlight housing bolts and it comes out. Not a real hard job and is Real straight forward. Good luck and have a good day.

Mar 27, 2009 | 2006 Subaru Outback

1 Answer

Power window fell down inside door


there are clips holding the door panel around the edges. to remove the clips, use a small screwdriver to feel for them, then use another one to pull the panel on the other side. Pull outward from both sides of the clip until it comes loose. Do this repeatedly, and then loosen and remove the arm rest.

Pull the window up and have a helper hold it as you work it back into the track.

Good luck.

Feb 15, 2009 | 2006 Saturn ION

1 Answer

Rear passenger side window stuck in down position


1) Yes you are right to think that it is the regulator.
2) You can repair this.

Remove the screws that hold the door panel on.
Remove the door panel. There are alot of clips on the door panel that just need to be pulled out with panel while removing.
Remove debris shield.(plastic piece between door panel and door.
The regulator will be visible at this point.
Disconnect the electrical connector from the regulator. Separate Glass from regulator. Some use clips some use bolts to hold the glass to the regulator.
Remove regulator attaching bolts.

Thats it just reverse the procedure for installation.

Aug 29, 2008 | 2006 Jeep Liberty

Not finding what you are looking for?
2006 Subaru Legacy Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...