Question about 2006 Chrysler Town & Country

Open Question

My town & country 2006 has this problem when

My town & country 2006 has this problem when we use the turn lights the front lights go off

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 85 Answers

SOURCE: Map light replacement on 2006 Town and Country?

Jun 17, 2009- ok I just looked at it. it is simple.
the lens pivots and presses a switch in on one end to make the light come on. take a butter knife or very small screw driver and reach in between the lens and the black center console. there you will CAREFULLY press a flat tab to the side that is made onto the lens ( I hope you dont break this tab).
on the very opposite position on the clear lens towards the door is where the lens has a tab that has a small hole in it. there is a plastic pin made onto the console trim that fits into this hole so the lens will pivot. this will give you an idea of which direction to pull the lens when you press in the tab,. it does look like it would break easily. I havent had to take mine off yet thankfully.
please visit again and rank this answer if this helps!... good luck

Posted on Jun 17, 2009

Ad
  • 412 Answers

SOURCE: Describe your 2006 Chrysler Town

P0404 IS EGR POSITION SENSOR PERFORMANCE..YOU NEED A NEW EGR VALVE..RECOMMEND DISCONNECTING BATTERY WHILE REPLACING EGR VALVE..SOMETIMES CODE WILL NOT GO AWAY EVEN AFTER REPLACING VALVE AND CLEARING CODE WITH SCANNER..VALVE IS LOCATED ABOVE ALTERNATOR ON END OF CYLINDER HEAD..THE BOTTOM BOLT CAN BE TRICKY TO REMOVE AND HAVE HAD TO REMOVE ALTERNATOR TO GET BOLT OUT..YOU WILL NEED A NEW GASKET FOR TUBE AS WELL..ABOUT 120 BUCKS FROM DEALER(CAN)

Posted on Jul 27, 2009

  • 125 Answers

SOURCE: i need to change front brake pads

You have two bolts to remove the caliper (it will still be attached to the flex hose). then use a C clamp to compress the caliper piston (one side on outside brake pad the other end on the back of the caliper). Inspect other components, replace pads and reinstall. I would highly recommend replacing rotors as well or at least having them turned. Its a pretty easy job if you have done similar jobs in the past.

Posted on Sep 04, 2009

  • 98 Answers

SOURCE: 2006 Town & Country ABS light stays on

when the abs light comes on your car is letting you know that it has shut down the abs system because of a problem. so you are braking with regular conventional brakes which is perfectly safe. any time a component of the antilock brake system malfuntions the abs system is shut off and the light will come on to let you know. the most common problem is that the wheel speed sensors go bad. a trouble code will be stored in the abs control module you can have the abs module scanned to see what the problem may be. But dont worry you car is safe to drive. you just dont have the antilock brake option.

Posted on Nov 02, 2009

  • 534 Answers

SOURCE: 2006 Town & Country burning oil excessively.

At 40K miles it shouldn't burn that much oil, unless the motor has been abused or overheated. With no signs of oil leaks, the engine must be burning it via the exhaust,

Change the oil (use a good quality oil) and then observe oil consumption.

If it still uses excessive oil check further as below:-
1) if it blows blue smoke on steady accelleration (pistons or ring wear),
or
2) only blows blue smoke on initial accelleration after a period of steady coasting or de-celleration (faulty valve stem oil seals).

Posted on Jan 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the internal fuse box on the 2006 Chrysler Town & Country?


You will find it beside the battery in the engine compartment. Black plastic cover.

Aug 18, 2014 | 2006 Chrysler Town & Country

1 Answer

What size battery do I need for our 2006 Town & Country?


  • SLI24 Battery 2001 to 2006 V6 3.8L 500CCA Town and Country Chrysler Car and Truck

Jan 25, 2011 | 2006 Chrysler Town & Country

1 Answer

I need the diagram of the 2006 Chrysler Town & Country fuse block.


For 2006 Chrysler Town & Country fuse diagram, check the Owners Manual (page 434 and next).

Hope this help (remember rated and comment this).

Mar 23, 2010 | 2006 Chrysler Town & Country

1 Answer

2006 Town & country makes clicking sound when breaking. Sounds as if coming from passenger side. Checked the front brakes & they're fine. They were repaced with new brakes & rotors 2500 miles...


As Chrysler says You may experience the following when the brake system go into Anti-lock.....The clicking of solenoid valves. When they changed the brakes did they damaged the ABS wheel speed sensor. It is mounted on the front axle on the back side of the brakes. Sensor & harness are one piece & must be replace toghter

Jan 15, 2010 | 2006 Chrysler Town & Country

1 Answer

How to get back sets removed from Town & country basic 2006 model


To remove the back seats.Lower headrest, fold seat down.Pull up on the release lever at the bottom on the right, tumble seat foward. Pull the release ******** the bottom of the seat to unlock the front

Dec 18, 2009 | 2006 Chrysler Town & Country

1 Answer

I need to change front brake pads


You have two bolts to remove the caliper (it will still be attached to the flex hose). then use a C clamp to compress the caliper piston (one side on outside brake pad the other end on the back of the caliper). Inspect other components, replace pads and reinstall. I would highly recommend replacing rotors as well or at least having them turned. Its a pretty easy job if you have done similar jobs in the past.

Sep 04, 2009 | 2006 Chrysler Town & Country

1 Answer

Missing flapper valve on an 06 town & country van's gas tank


I doubt if that is the reason your check engine light is on. It is more likely an o2 sensor. However make sure your cap is tight when you add gas and don't leave the engine running while the cap is off. That can trigger the light

Jul 03, 2009 | 2006 Chrysler Town & Country

Not finding what you are looking for?
2006 Chrysler Town & Country Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...