Question about 1996 Chevrolet Blazer

2 Answers

Looking for brake fluid sensor in a 1996 chevy blazer

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 142 Answers

This will be on the side of the master cylinder,"where you put the brake fluid in" it will be the only sensor there

Posted on Sep 27, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 439 Answers

The sensors are normally located on the bottom of the master cylinder. It will be the only thing on the cylinder with a plug in.

Posted on Sep 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake issues on 1996 Chevy Blazer


You should check your vacuum lines make sure they are all connected plus the line you keep disconnecting is collasping onto its self which in turn will make the brakes stick so you must have one of the ends plugged.

Jul 25, 2012 | 1996 Chevrolet Blazer

1 Answer

Will a throttle position sensor cause my 96 model Chevy blazer 4.3L vortec get bad gas mileage I'm only getting 225 miles to a full tank


I would replace both o2 sensors and take the mass air flow sensor off and clean it with a non-chlroated brake cleaner.Also a tune-up sure won't hurt sparkplugs,plug wires,distributor cap and rotor.Your fuel milage should increase.

Jan 13, 2012 | 1996 Chevrolet Blazer

1 Answer

My parking brake light is on and i cant get it to go off its not engaged and i checked the switch its not it. can you help?? its a '91 chevy s10 blazer 4.3 fuel injected 2x2


The brake light can come on for two reasons. I is the brake pedal is engaged witch you have found is not the case. The other is because the brake fluid is low or the sensor that monitors brake fluid level is defective.

Check the brake fluid level, if its full unplug the switch and see if it goes out. I'm not sure if the switch completes the circuit when the level is low or opens the circuit but its worth a shot.

Sep 25, 2010 | 1991 Chevrolet S-10 Blazer

1 Answer

What does a ABS sensor look like on a 97 chevy blazer


mid size blazer- take off wheel-brake caliper-brake caliper bracket- rotor-and behind the hub u will see a wire going into the back of hub and is secured by a hex/torx head bolt that is ur abs sensor it looks like a small cylinder with wires attached---on the s-10 blazer some of the abs sensors set ups-- are part of the hub assembly/wheel bearing would have to change the whole unit

Mar 05, 2010 | 1997 Chevrolet Blazer

2 Answers

I have a 2001 Blazer and the anti-lock brake light and the brake light are on. What should i do?


Check the brake pads lining ,both front and rear,if the lining is nearly replace it ,then the light will switch off,check also the brake fluid level.

Jan 12, 2010 | 1996 Chevrolet Blazer

1 Answer

Need help with 1996 Chevy Cavalier clutch problem


HI look under car in between transmission and engine look for sign of clear fluid like brake fluid.If you don't find any replace your clutch master cylinder.

Sep 26, 2009 | 1996 Chevrolet Cavalier

1 Answer

1996 Chevy Blazer wont shift into 3rd just that simple fluid ok ,looked at vacume lines???


could be your cad coverter does it make any noise when your driving

Jan 24, 2009 | 1996 Chevrolet Blazer

2 Answers

Blazer runs awful....


i had the same issue after having replaced the egr sensor and the O2 sensors turns out the fuel pump was bad.

Dec 30, 2008 | 1996 Chevrolet Blazer

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...