Question about 1981 Ford F 100

1 Answer

My fuse box has a burnt out connector for the turn signals

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 832 Answers

Replace it with a new connector, and have it reconnected.

Posted on Sep 27, 2009

Testimonial: "I will try your remedy today"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal doesn t work


The turn signal relay is next to fuse box under dash. more than likely its burnt out. Good-day!

May 04, 2014 | 2000 Saturn L-Series

1 Answer

How do i fix a short in my fusebox


You do not have a shorted fuse box, you have a shorted trun signal circuit. The fuse just blows due to the short in the wiring or switch, not in the fuse box.

Jan 25, 2012 | 1996 Jeep Grand Cherokee

1 Answer

I have a Honda Accord 2000 6 cyl. I have 3 brake lights, and the only light working is the top one-the other 2 do not light up you hit the brake pedal.. All my lights work, hazards, left/right turn signal,...


there is a little box on the left side of the trunk in the brake lamp harness chances are this little control unit burnt up. find it and unplug it and make sure the connector did not get burned also take the box apart it will have some tabs by the connector end to slide the inside out check the printed circuit board to see if it is burnt.If it is it will cost you about a hundred bucks from the dealer.

May 14, 2011 | 2000 Honda Accord

1 Answer

I wired my 2011 Kia Sorento with a converter and 4 wire flat connector for my utility trailer. The wiring confirmed correct by using a circuit tester. There is signal going in and signal coming out of the...


you need a adapter for the flashing lights left and right as well the brake lights are seperate along with parking lights for the electric brakes you have to run a power direct to battery with circuit breaker installed on the line but if you look under the bumper near the drivers side in the back you have a connector installed by the company and you might be able to use it if that is what you did then you have to check the fuses because everthing is installed except the fuse for the connector so if thats what you did check the fuse box for missing fuses or burnt so green wire for right, white ground ,brown parking,yellow left the brake lights go through the adapter so check it out

Mar 22, 2011 | Kia Sorento LX Cars & Trucks

1 Answer

Lost my headlights,tail lights,turn signal,and dash lights,have no power in the fuse box on the inside


behind the fuse box there is a gray connector. check the red/white wires on either side of the connector for 12 volts. if no voltage on either side replace 40 amp fuse in engine compartment fuse box, if voltage on only one side, repair the connector connection overheats and melts inside the connector

Oct 15, 2010 | 2001 Chrysler PT Cruiser

1 Answer

WHAT FUSE DO I CHANGE FOR THE SIGNAL LIGHT?


The fuse box under the dash board is marked as turn signal which is normally a 15 amps fuse.
Using a good light you can look into each fuse to see the burnt on as being tranparent the wire will be burnt if the fuse has blown.

Sep 16, 2010 | 1997 Honda Accord

1 Answer

Turn signals and hazard lights won't work. already replaced flasher unit and burnt bulbs but still no turn signals


Check the Fuse box loacted inside the hood. Look for the guidance on the top of the fuse box for locating trun signal fuses.

Check whether they are good. If not replace with correct rating fuse. If the problem is not solved still, wiring harness has to be checked as the bulbs & flashers are replaced already.

Jun 04, 2010 | 2002 Hyundai Accent

1 Answer

I had a burnt bulb in my rear left turn signal. I replaced it but it doesn't blink. Is ther a fuse I should check and which one, my book is not specific


there is now fuse for each bulb just for the entire signal and hazard system, I would assume that the connector is faulty, it is common. If you use a test light on the wire going for the signal it will probably test good. if this is so then just change the connector.

Oct 07, 2009 | 2005 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...