Question about 1991 Volvo 240

1 Answer

How to take the sunroof panel out - 1991 Volvo 240

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 20 Answers

1. roll roof back 4 inch.
2. Pull down on front of modest cover to unclip
3. push modest cover all the way back in roof.
4. close sunroor and tilt open
5. remove the screws on track.
But why?
This is one of the hardest roof to repair, the seal is a bear to replace. I way the problem out first.

Posted on Sep 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sunroof does not open. Fuse is ok and the shade operates normally.


Do you know how to do automotive electrical testing ?????? How to read a wiring diagrams ???? http://www.bbbind.com/free_tsb.html .Videos on youtube Ohms Law Tech Tip from L1 with Dave Hobbs Copy of Voltage Drop Essentials TST Motor Age The only way to find the problem , testing !

Sunroof Description and Operation (One Connector System)
Sunroof
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
• Open
• Vent
• Closed
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.

Your best bet , take it to a qualified repair shop or buick dealer .

Feb 10, 2017 | 2010 Buick LaCrosse CXS

Tip

2002 Jaguar XType Sun-roof one-touch operations reset


I had this issue and found the solution around, worth sharing and it takes 30 seconds: <br /> <span> <li>Press the sunroof switch forward to move the sliding roof panel into the tilted position.</li> <li>Release the sunroof switch.</li> <li>Press and hold the sunroof switch forward until the sliding roof panel moves slightly. This may take 30 seconds or more.</li> <li>Release the sunroof switch.</li> <li>Immediately press and hold the sunroof switch in the forward position. The sliding roof panel will move down and rearward to the open position, and then forward into the closed position. Do not release the sunroof switch until the sliding roof panel has stopped completely.</i></li> <li>Your sunroof panel should now be aligned.</li></span>

on Jul 11, 2011 | 2002 Jaguar X-Type

1 Answer

WHERE CAN I DOWNLOAD A 2004 CADILLAC CTS REPAIR MANUEL?


Here's a description the sun roof
Power Sunroof System Components
The power sunroof system consists of the following components:
• Sunroof module
• Sunroof switch
• Sunroof motor, with 2 hall effect sensors and limit switch
• Sunroof window
• Sunroof sunshade panel
• Power supply for the sunroof module: RAP 25 A
• Ground G402

Override
The override function is used when needing to force a closing of the sunroof window. To override the system:
Turn ignition to ON.
Rotate the sunroof switch to the close position.
Press upward.
The sunroof switch data 6 circuit, or override circuit, will become grounded at the sunroof module. As long as the sunroof module sees this input, it will continue to slide the sunroof window to close, regardless of the other sunroof switch data circuits inputs.

Oct 28, 2016 | Cadillac Cars & Trucks

1 Answer

Where are drains located on a 2003 chevrolet impala sunroof?


They go down inside front A pillar an inside rear D pillar . To get at them you need to take trim off an the headliner down .
Sunroof Housing Rear Drain Hose Replacement (Impala)
Remove the headliner. Refer to Headlining Trim Panel Replacement in Interior Trim. Remove the rear quarter lower trim panel. Refer to Rear Quarter Lower Trim Panel Replacement in Interior Trim. Disconnect the rear sunroof drain hose from the sunroof module rear spigot. Remove the tape from the rear sunroof drain hose tube.
Disconnect the rear sunroof drain hose from the rear sunroof drain hose tube. Remove the rear sunroof drain hose tube from the upper retainer clip. Remove the rear sunroof drain hose from the rear pillar
The front is simalier .

Dec 22, 2015 | 2003 Chevrolet Impala

2 Answers

How to install replacement sunroof motor on a 1999 Pontiac grand prix


Important: This sunroof system is timed from the factory in order to allow the actuator to shut off automatically when the sunroof window reaches a certain position. Use extreme care when removing the actuator from the sunroof module. This may cause the timing to be thrown off. This may damage to the sunroof. Anytime the actuator needs to be removed from the module, ensure that the sunroof window is in the fully closed position.
Remove the sunroof window. Refer to Sunroof Glass Panel Replacement .
Slide the sunshade fully rearward. Move the sunroof window to the vent position. Remove the sunroof screws (two on each side). Remove the sunroof window from the module.
Place the sunroof module in the fully closed position. Remove the headliner. Refer to Headlining Trim Panel Replacement in Interior trim.
Tools Required ?€¢
J 38778 Door Trim Pad and Garnish Clip Remover


?€¢
J 2772-C Headliner Installer

  1. Remove the sunshades. Refer to Sunshade Replacement .
  2. Remove the overhead console, if equipped. Refer to Roof Console Replacement .
  3. Remove the sunshade retainers. Refer to Sunshade Anchor Replacement .
  4. Remove the power sunroof switch, if equipped. Refer to Sunroof Switch Replacement in Roof.
  5. Remove the sunroof trim lace, if equipped. Refer to Sunroof Seal/Molding Replacement in Roof.
  6. Remove the dome light, if equipped.
  7. Remove the coat hooks. Refer to Coat Hook Replacement .
  8. Remove the assist handles. Assist Strap Replacement
  9. Remove the rail lamp. Refer to Roof Side Rail Lamp Replacement in Lighting.
  10. Remove the windshield side garnish molding. Refer to Windshield Pillar Garnish Molding Replacement .
  11. Remove the upper quarter trim panels. Refer to Rear Quarter Upper Trim Panel Replacement .
  12. Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement .
  13. Pull down on the door opening weatherstrip seal on both the front and the rear doors.
  14. Remove the 2 rear retainers (2) using J 38778 Door Trim Pad and Garnish Clip Remover. Disconnect the headliner electric harness at the right side of the rear window shelf. Rotate the right front seatback to a horizontal position. Remove the headliner from the vehicle through the right front door.
Disconnect the electrical connector from the actuator.
Important: Before removing the actuator, ensure that the pins J 41718 are tight and holding the cable.
Thread the J 41718 into the front sunroof window screw hole in order to retain the cable adjustment. Remove the sunroof actuator screws. Remove the sunroof actuator from the module. Did you look for a video on youtube ?

Feb 27, 2015 | 1999 Pontiac Grand Prix

1 Answer

Panoramic sunroof panels colliding 2007 Pontiac G6


it sound like there is a problem with the cables _ they either streched or catching on something or just could be worn out also

Oct 28, 2014 | 2007 Pontiac G6 GT

2 Answers

Sun roof does not work. how do you fix it. ?


Hi,

  1. Open the fuse panel. Turn the knob on the fuse panel cover counterclockwise or push in on the release tabs on the fuse panel cover (depending on the year of your Toyota), and pull down on the fuse panel cover.
  2. Pull the fuse for the sunroof out of the fuse panel using the fuse pullers in the fuse panel. Use the diagram on the underside of the fuse panel cover if you are having trouble locating the fuse for the sunroof.
  3. Check the metal strip in the middle of the fuse. The strip should not be burned or damaged. If it is, replace it with a fuse of the same amperage.
  4. Check the recessed track of your sunroof. Clear away any debris that may be stuck in the sunroof's track. Use engine degreaser and a wire brush to clean the track of dirt. Then, wipe the track down with clean paper towels.
  5. Apply hard grease to the sunroof wheels and track so that the sunroof can move easily once again.
Best regards

Oct 29, 2010 | 1990 Toyota Celica

1 Answer

My 05 honda accord sun roof wont open


Hi,

The sunroof on your Honda may not be operating correctly. The most common problems with Honda's sunroofs is the track. This is especially true of early 1990s Honda vehicles. However, many Hondas use a recessed track that easily collects and traps dirt and debris. When this happens, your sunroof may not close and seal properly. Another minor problem is a blown fuse on some model years of Honda vehicles. Before fixing anything, however, troubleshoot the problem.
  1. Open the fuse panel. Turn the knob on the fuse panel cover counterclockwise or push in on the release tabs on the fuse panel cover (depending on the year of your Honda), and pull down on the fuse panel cover.
  2. Pull the fuse for the sunroof out of the fuse panel using the fuse pullers in the fuse panel. Use the diagram on the underside of the fuse panel cover if you are having trouble locating the fuse for the sunroof.
  3. Check the metal strip in the middle of the fuse. The strip should not be burned or damaged. If it is, replace it with a fuse of the same amperage.
  4. Check the recessed track of your sunroof. Clear away any debris that may be stuck in the sunroof's track. Use engine degreaser and a wire brush to clean the track of dirt. Then, wipe the track down with clean paper towels.
  5. Apply hard grease to the sunroof wheels and track so that the sunroof can move easily once again.
Best regards.

Oct 28, 2010 | 2005 Honda Accord

1 Answer

Sun roof won't open, but i hear the motor turning


Check for any obstruction in the rail.

Also, can check this procedure to test your components...
Power Sunroof - REMOVAL & INSTALLATION (click over pic for zoom)

Motor
See Figure 1
  1. Remove the sunroof switch panel by pushing it to the side and disengaging the pawl, then pulling it downward.
b5908ae.jpg

Fig. 1: The sunroof switch panel is retained by a metal clip
  1. Remove the sunroof switch bracket.
  2. Unplug the sunroof motor wiring harness connectors.
  3. Remove the sunroof motor mounting screws.
Disassembly of the sunroof motor is not recommended.

To install:

  1. Lightly lubricate the drive gear with grease and install the sunroof motor to the sunroof assembly.
  2. Plug in the electrical harness connectors to the sunroof motor.
  3. Operate the sunroof to verify proper operation.
  4. Install the sunroof switch bracket and the sunroof switch panel.

Sunroof
See Figures 2 and 3

abc86a3.jpg

Fig. 2: Exploded view of the sunroof assembly on 1993-94 vehicles

515e4a7.jpg

Fig. 3: Exploded view of the sunroof assembly on 1995-97 vehicles-1998 models similar
  1. Tilt up the sunroof lid.
  2. Remove the lid side trim.
  3. Remove the lid bolts and the lid assembly.
  4. Remove the rear drain mount screws and the drain.
  5. Remove the shade assembly holders from the sunroof frame.
  6. Remove the shade assembly.
  7. Remove the sunroof switch, interior accessories and headliner.
  8. Remove the switch bracket.
  9. Remove the motor assembly, spacer and clip.
  10. Remove the wind deflector mount holders from the sunroof frame.
  11. Remove the wind deflector.
  12. Disconnect the drain hose.
  13. Remove the sunroof brackets.
  14. Remove the sunroof frame assembly.
  15. Remove the link and wire assemblies.
To install:
  1. Tilt up the sunroof lid.
  2. Install the link and wire assemblies.
  3. Install the sunroof frame assembly.
  4. Install the sunroof brackets.
  5. Connect the drain hose.
  6. Install the wind deflector.
  7. Install the wind deflector mount holders on the sunroof frame.
  8. Install the motor assembly, spacer and clip.
  9. Install the switch bracket.
  10. Install the sunroof switch, interior accessories and headliner.
  11. Install the shade assembly.
  12. Install the shade assembly holders on the sunroof frame.
  13. Install the rear drain mount screws and the drain.
  14. Install the lid bolts and the lid assembly.
  15. Install the lid side trim.

Hope helps (remember rated this help).

Jun 03, 2010 | 1996 Nissan Maxima

1 Answer

The sliding panel under my sunroof is broke. Any suggestions? The Sunroof motor is working.


The sunshade clips are probably broken. Need to remove the glass panel. Note the position of the panel the frt and the rear. If not properly reinstalled you might get wind noise. Once you have the panel removed unscrew the clips from the sunshade. Carefully remove the shade and install the new clips.

May 26, 2009 | 2002 Volkswagen Jetta TDI

Not finding what you are looking for?
1991 Volvo 240 Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...