FRONT GRAB HANDLE INSTALLATION FOR FORD EXPEDITION
PASSENGER SIDE FRONT GRAB HANDLE (THIS IS THE FAKE PLASTIC WOOD HANDLE ABOVE THE GLOVE BOX) INSTALLATION FOR FORD EXPEDITION 2005. NEED INSTALL INSTRUCTIONS AS THERE DOESNT APPEAR TO BE ANY SCREWS VISIBLE.
An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 100 times.
Re: FRONT GRAB HANDLE INSTALLATION FOR FORD EXPEDITION
Empty glove box.with box open,squeeze sides of box inward to release ''ears'' at top of back of box box will hinge down towards floor.look inside for mounting screws passing from inside of dash into handle
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Are you looking for the front or rear? The front is behind the glove compartment on the passenger side. The rear one is on the passenger side to the right of the rear third row seat behind the plastic panel.
The 2003 Expedition smart junction box was formerly called a GEM module in previous years. It has relays that control your keyless entry codes, the relays that control the dome lights and the delayed radio shutoff as well as other functions.
On a 2003 Expedition, the sjb (smart junction box) is located on the inside passenger's side kick panel below the glove box. It is most easily accessed by opening the glove box and squezzing the limiting tabs on each side so the glove box can open fully and tilt forward. It is approximately 6" long by 4" tall and about 1 3/4" thick. The part number on the label will be 2L1T-15K602-AN or similar for 2003 Expeditions.
PCM Ford's Location:
* Ranger - behind instrument panel (cowl), center to both driver and
* Explorer/Mountaineer - behind instrument panel (cowl), (access from
engine compartment dash panel) on passenger side to center of vehicle.
* All other F-Series, Expedition/Navigator - lower dash panel on
* Excursion - lower dash panel on driver side.
The PCM is behind the glove box and has a big harness connector in the
firewall that you access from the engine compartment. REMOVAL & INSTALLATION
Fig. 1 The calibration number will be needed to order such
parts as a replacement PCM, various sensors, and almost any emission
control component. Typically this number is attached to a label found on
the driver's door or the door pillar
1997-00 F-150, F-250, Expedition and Navigator
Fig. 2 Loosen the connector retaining bolt and remove the PCM
Fig. 3 Remove the passenger side front door scuff plate
Fig. 4 Remove the passenger side kick panel
Fig. 5 Remove the PCM bracket clip and remove the PCM
Remove the battery and the battery tray.
Loosen the connector retaining bolt and remove the PCM connector.
Remove the passenger side front door scuff plate.
Remove the passenger side kick panel.
Remove the PCM bracket clip.
Remove the PCM.
Installation is the reverse of removal.
Tighten the PCM connector retaining bolt to 36-44 inch lbs. (4-5
This is for the front passenger side door panel from a 1999 Ford Expedition. The
driver's side door should be the same, except for the mirror switch
which needs to be unplugged. The 1998 *might* be the same, I don't know,
but this should be helpful to someone.
Use a flat blade screwdriver or other suitable tool to pry out on the
top of the triangular plastic panel on the top front of the door panel.
The plastic holder should pull out of the door. Now pry up on both sides
of the triangular panel and pull it loose. Remove the philips head
screw you find under this panel. Pull the door latch handle, pry out the
insert where the handle goes through, and remove the bolt that holds
the door handle in place. Remove the door handle. Pry up on the ends of
the door switch panel to remove it. Unplug the cables by pushing in on
the lock tab on the side of the plug and pulling out. Remove the philips
head screw accessible through the switch panel hole. Insert a flat
blade screwdriver into the slot at the bottom of the courtesy light lens
and pry up and out to remove the lens. Remove the philips head screw
behind this lens. Pull up on the door panel to remove it. Be careful of
the courtesy light when removing the panel - give the light a quarter
turn counter-clockwise from the rear to remove it from the door panel.
Its possible that this GUIDE can helpfull as reference.
on the top of your dash you should have an access panel, inside that opening there are three screws that are put in (direction) from front to back, two are relatively easy to get to and see, the third is above the passenger side a/c vent outlet. Also there are two on each end of the dash, that you have to remove the door weather stripping to reach, hope this helps, let me know
Both above answers are not right... I just replaced the Pass side power mirror assembly on my 97 Expedition. No heat, no directional. The inside door panel must come off. 1. pry off interior triangular plastic trim piece inside of door at mirror area. Remove door panel screw at this area. 2. Pry off power window switch panel and remove door panel screw at this area. 3.Remove interior door light cover and remove screw at this area. 4. Remove plastic cover at door handle. 5. The interior door panel can now be lifted up to release it from it's fasteners. 6. Disconnect light and push power window switch assembly through the door panel and it can be set aside. 7. Disconnect mirror power at coupler. 8 Loosen three mirror mounting screws with 7/16 socket. DO NOT unscrew completely.. the will fall down the door cavity. Use a round magnet on holder to remove the screws completely. 9.Thread electrical connection into door panel and install mirror. 10. Smile when mirror works and drink a beer! rayman
There is a triangular piece, at top corner, covering a screw behind the
mirror. Remove that screw. Remove the piece that covers the handle and
remove the screw holding the handle to the door. Look through, where
door handle was and remove another screw just above where the handle
was. This screw is holding the panel to the actual door. Pop the cover
off for the automatic door locks and disconnect them. Lift the panel in
an upward direction.