Question about 2003 Chevrolet S-10

1 Answer

How do i get the fan shaft off so i can get the water pump out?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

There is a tool for it but you can use a big wrench put it on the fan shaft nut with the belt still on so it holds the pullley, give the wrench a quick hit to the left with a hammer to break loose then spin off.

Posted on Sep 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

About water pumps


most of the water pumps on cars had a hub pressed onto the pump shaft and 4 small bolts holding the pulley onto that hub
even viscous fan hubs ( fan clutch) is bolted to the hub pressed onto the shaft
comment with a photo of the water pump that has the bolt in the middle and comment on the engine make and model

Oct 17, 2015 | Cars & Trucks

1 Answer

Leaking water behind fan


The water pump is directly behind your fan clutch. Most probably, it's the pump. Shaft seal is already worn out (maybe because of damage bearing). You have to replace the whole assembly or replace the shaft, seal, and bearing. These items are within the repair kit that you can buy in parts store.

Oct 23, 2012 | 1985 Cadillac Seville

1 Answer

Leaking antifreeze from the fan pully. is the fan pully the water pump


Hi,
The water pump will be directly behind the fan pulley. The fan pulley mounts onto the water pump shaft. So no the fan pulley is not the water pump.
Safe Journey's,
Wayne

Aug 17, 2011 | 2005 Dodge Ram 1500

1 Answer

Need to replace fan clutch


disconnect barrery, remove bolts holding fan shroud, at thr water pump where the fan shaft attaches unscrew the nut, it will remove the fan from water pump, lift out fan and shroud, 4 bolts holding clutch and fan

Feb 08, 2011 | 1998 Jeep Grand Cherokee

2 Answers

How do you remove the fan from 1998 f150 4.2 liter


how do you remove the fan and fan clutch from 1998 f150 4.2 liter engine. i am trying to replace the water pump but i cannot get the fan to break loose . i cannot figure how to stop pump from turning while trying to loosen the bolt or nut that holds the fan clutch on the water pump shaft . is there a special tool to help me with this

Jul 15, 2010 | 1998 Ford F150 Regular Cab

2 Answers

While running the air conditioning, the air cools and then warms and eventually cools for a little bit again. I think the water pump is what's needed here? what is the big bolt behind the fan?


It is unlikely that the water pump is causing the trouble you describe. The large hex behind the fan is what you would turn to remove the fan clutch from the water pump shaft. This fan clutch is supposed to detect heated air coming through the AC condenser and radiator and engage the fan more positively with the water pump shaft when more air needs to me moved to cool the radiator and AC condenser. The fan clutch could be bad or the AC system may not be properly charged--either of these conditions could cause the problem you describe.

Feb 25, 2010 | 2005 Dodge Ram 1500

1 Answer

Fan & shrould Broke off the water pump


I believe that the part your'e talking about is the clutch for the fan. It is a two piece unit, factory assembled. likely the bearing inside failed and caused this. You can change the fan and clutch unit, inspect everything for damage from the fan becoming disconnected and be OK, however running and wobbling may have caused some bearing damage in the pump...keep an eye on it...any noises or leaks from there, change it.

Mar 24, 2009 | 1995 Nissan Pathfinder

1 Answer

Water pump removal


yes , you need a special tool to remove fan clutch to shaft

Mar 01, 2009 | 2003 Hummer H2

2 Answers

94 fleetwood brougham LT1 overheating


This engine has a cam driven water pump. If the gear is sheared/broken it can cause this issue.

Feb 23, 2009 | 1994 Cadillac Fleetwood

1 Answer

Changing the water pump on 2000 Jeep Grand Cherokee V6


WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Jan 10, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2003 Chevrolet S-10 Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...