Question about 1993 Saturn SL2

1 Answer

My odometer and trip odometer are not working. Are there any new instrument clusters available? The assembly looks difficult to take apart and I'm willing to purchase a new one after exploring then repair of used possibilities. Renee

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

Look on ebay, instrument clusters abound. Make sure you have the right year and model as most look similar

Posted on Sep 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2002 Saturn L100 odometer stopped working and isn't clocking miles at all.


Odometer
The odometer is an electronic digital display. Digits displayed are illuminated by the odometer backlight bulb. The odometer backlight bulb brightness is controlled by class 2 messages from the BCM to adjust the display for daylight and instrument panel dimming operation. The trip odometer and total odometer will show in this display area. The push button in the lower right side of the speedometer is used to toggle between the trip and total odometer readings. To reset the trip odometer, push and hold the button down for at least two seconds. The total odometer display has six digits with no decimal display. The trip odometer has four digits including a decimal point and indicates tenths of a mile or kilometer.
The body control module (BCM) stores the vehicle mileage. If the BCM fails, the cluster will display the last valid mileage that was sent before the BCM failed. For replacement of the BCM refer to the BCM section of this service manual. Replacement instrument clusters do not require odometer pre-setting before installation. If the instrument cluster is replaced, the mileage stored in the BCM will be sent to the new cluster via serial data, and shown in the odometer display.

Your best bet , take it to a qualified repair shop.

Jul 25, 2017 | Saturn Cars & Trucks

1 Answer

On a2000buick century odometer not working


You would need to take it to the dealer or someother qualified repair shop that has the diagnostic tool to check for DTC'S - diagnostic trouble codes in the instrument cluster .
DTC B0570 Season Odometer Malfunction

The instrument cluster receives a vehicle speed input from the vehicle speed sensor (VSS) over the Class 2 line. This signal is used in order to drive the speedometer and the odometer of the instrument cluster. The instrument cluster will compare the VSS data with a 16-point look-up table in order to determine needle deflection. A smooth filter is used in order to secure a continuous response. The season odometer displays the total accumulated kilometers (miles) of the vehicle. This value is permanently stored in the Electronically Erasable Programmable Read Only Memory (EEPROM) of the instrument cluster. The trip odometer displays the accumulated kilometers (miles) to the tenths of a kilometer (mile) since the last reset. This value is stored in Keep Alive Memory (KAM) of the instrument cluster.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
Always perform the Instrument Cluster Diagnostic System Check before attempting to diagnose this DTC.
This diagnostic procedure requires using a scan tool.
This repair procedure requires instrument cluster replacement.
Step
Action
Value(s)
Yes
No
1
Did you perform the Instrument Cluster Diagnostic System Check?
--
YES - Go to Step 2
NO - Go to Diagnostic System Check - Instrument Cluster
2
Using a scan tool, clear the instrument cluster DTC and retest for DTC B0570.
Does DTC B0570 reset?
--
Go to Step 3
Go to Powertrain On Board Diagnostic (OBD) System Check in Engine Controls - 3.1L or Powertrain On Board Diagnostic (OBD) System Check in Engine Controls - 3.8L
3
Replace the instrument cluster. Refer to Instrument Cluster Replacement .
Is the repair complete?
--
System OK
Go to Diagnostic System Check - Instrument Cluster
© 2017 General Motors Corporation. All rights reserved.

Feb 27, 2017 | 2000 Buick Century

1 Answer

Hi i have a 1995 ford mustang 3.8 v6 5 speed my trip meter doesnt work ive had the instrument cluster replaced and still dont work odometer and tach work just not the trip how to fix thanks


Fords in that era are notorious for broken plastic gears in the assembly. If the Speedometer works and the odometer works but the trip odometer does not work, you can still have a broken or stripped plastic gear. They are very small and cost about $25 but they are a pain to replace. You can send your cluster off to have it repaired by a reputable shop. Just Google instrument cluster repair.

Dec 17, 2014 | Cars & Trucks

1 Answer

After disconnect and reconnect the battery of my opel antara, the indication of odometer displays only 888... for all indications. How can i reset it?


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2007 Opel Antara 2.0

1 Answer

My nissan Almera S reg has no side lights or dash lights.All fuses seem ok.


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2005 Nissan Almera 1.5

1 Answer

Changing dashboard light


Hi,

This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Aug 09, 2010 | 1998 Plymouth Voyager

3 Answers

Odometer stopped working


IF YOUR SPEEDO IS WORKING THEN YOUR VSS IS OKAY, BAD VSS WILL STOP SPEEDO AND USALLY CAUSE HARD SHIFTING. NORMALLY ODO IS CONTROLLED BY SERVO MOTOR WHICH MAY HAVE WENT OUT. CHECK EBAY FOR REPAIR SERVICES OR SIMPLY GET A SALVAGE CLUSTER AND HAVE MILEAGE RESET

Jun 28, 2009 | 1998 Ford Mustang

2 Answers

1995 Cougar Odometer/trip-meter inop


Section 13-01: Instrument Cluster—Conventional 1995 Thunderbird, Cougar Workshop Manual REMOVAL AND INSTALLATION Instrument Cluster Removal and Installation
  1. Disconnect battery ground cable (14301) .
  1. Remove screws holding instrument panel reinforcement (017A28) .
  1. Remove screws holding instrument panel lower shield (045G02) .
  1. Remove fasteners holding steering wheel column as outlined in Section 11-04 . Gently lower steering column.
  1. Remove fasteners holding the instrument panel finish panel (044D70) and gently pry off.



  1. Remove four instrument cluster retaining screws. (Do not remove screws from the instrument cluster main lens (10887) and instrument cluster mask (10890) ).
  1. Slide the instrument cluster (10849) to the right of the instrument panel opening and unhook the instrument panel harness from the back of the instrument cluster .
  1. Remove the instrument cluster from the instrument panel (04320) .
-----------------------
Speedometer/Odometer Federal law requires that the odometer in any replacement speedometer (17255) must register the same mileage as that registered in the removed speedometer . Since the speedometer mileage cannot be reset on this unit, affix odometer sticker to driver's door pillar and record original vehicle mileage. Removal
  1. Disconnect battery ground cable (14301) .
  1. Remove the instrument cluster (10849) as outlined.
  1. Remove seven screws retaining the instrument cluster mask (10890) and instrument cluster main lens (10887) .
  1. Remove speedometer assembly.
Installation
  1. Position the speedometer assembly to the instrument cluster back plate (10848) and install.
  1. Position the instrument cluster mask and instrument cluster main lens to the instrument cluster back plate and install the seven retaining screws.
  1. Install the instrument cluster as outlined.
  1. Connect battery ground cable and check the operation of the speedometer .
please rate if this helps

Mar 24, 2009 | 1994 Mercury Cougar

1 Answer

Odometer only works at night


THE PROBLEM IS A BAD OR SHORTED PINS OR CHIP, SO YOUR BEST BET IS THAT, TO REPLACE THE CLUSTER, SORRY.
ALL NEW CLUSTERS ARE ELECTRICAL NOW.
WHAT YOU CAN TRY IS TAKE THE CLUSTER OUT AND LOOK FOR ANY BLOWN RESISTOR OR METAL CARRIER.
IF IT WORKS AT NIGHT THE LIGHT SWITCH IS SENDING THE POWER TO THE UNIT. AT DAY TIME ANOTHER SOURCE IS SENDING POWER TO IT. SO THAT CHANNEL MAY BE BLOWN.

May 29, 2008 | 2005 Ford Taurus

Not finding what you are looking for?
1993 Saturn SL2 Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...