Question about 2006 Chevrolet Silverado

1 Answer

How do you remove spark plug wires from 2006 silverado

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 753 Answers

Twist and pull only on the boot part of the wires they do come off very hard after they have been on for a long time.

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It cranks but it won't start. I got a new battery, cam position senor and crank position sensor. took out the ignition control was told that was still good.


Check for spark at the plug wires to spark plugs, no spark on anything, then suspect a fouled job replacing the cam position sensor.

Oct 03, 2011 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

How can I replace the spark plug for my toyota sienna 2006


Hi. Here's the procedure on how to change the spark plugs.

  • Step 1 Connect the spark plug socket to the socket extension.
  • Step 2 Open the hood and pull the spark plug wires off the top of the engine. You may need to wiggle them back and forth while pulling up on the plug wires in order to remove them.
  • Step 3 Lower the spark plug socket into the engine and push the socket over the top of the spark plug.
  • Step 4 Turn the spark plug counterclockwise with a socket wrench to loosen and remove it from your Sienna's engine.
  • Step 5 Pull the old spark plug out of the socket and insert a new spark plug into the socket with the electrodes facing out.
  • Step 6 Lower the spark plug into the engine and thread and tighten the spark plug.
  • Step 7 Slide the plug wire down into the plug well and push it over the top of the spark plug until it seals the plug. The wire should fit nice and snug over the spark plug.
  • Aug 15, 2010 | 2006 Toyota Sienna

    1 Answer

    Where can I find the Ignition Coil in a 2006 Ford Taurus?


    Ignition Coil adobe.gif Printable View (79 KB) Removal and Installation
    1. ani_caut.gif CAUTION: It is important to twist the spark plug wire boots while pulling upward to avoid possible damage to the spark plug wire.
      ani_caut.gif CAUTION: Spark plug wires must be connected to the correct ignition coil terminal.
      Disconnect the 6 spark plug wires from the ignition coil by twisting while pulling upward.
    1. Disconnect the ignition coil electrical connector.
    1. Remove the 3 bolts and the ignition coil.
      • To install, tighten to 6 Nm (53 lb-in).
    1. To install, reverse the removal procedure.
    fbf58a7.jpg

    Hope this helps.. Cobra

    Jun 12, 2010 | 2006 Ford Taurus

    1 Answer

    When to do a tune up on a 2006 chevrolet silverado


    Hello, the spark plugs are good for 100,000 miles on this vehicle. when you get close to 100,000 miles is when you should tune it up

    May 20, 2010 | 2006 Chevrolet Silverado

    1 Answer

    I have a 2006 F150 with a 5.4. I have a engine


    First remove spark plug. #8 plug is, if sitting in truck, left rear plug. Have someone crank engine while you hold spark plug, connected to plug wire, ground plug to ground. Check spark. If no spark, remove plug wire from coil, connect test light from coil to ground, see if you get spark, if no spark replace coil. Leave cylinder #8 open to air to dry any unburnt fuel in cylinder.

    Sep 25, 2009 | 2006 Ford F-150

    1 Answer

    Remove spark plug wires from a 2005 silverado 5.3 engine


    just check it first and see how its fitted ,its only a shroud

    Jun 14, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

    1 Answer

    How do I get the spark plug wires off to change the plugs on my 2006 Silverado?


    there is a special tool, go to any good parts store like NAPA to buy one, around $10 ask for spark plug boot removal pliers

    May 12, 2009 | 2006 Chevrolet Silverado

    1 Answer

    How to remove the spark plug wires


    This is Totally Common when the Plug Wire Boots have Not been Lubricated Before Installation. Get a Pair of Pliers and Move Back and Forth While Pulling and they will Come off. It will not be Easy, Even if the are the Factory Wires. Make Sure and Use the Lube that they come with on the Next Install. Please Rate my Response, I need all the Help That I can Get! Thanks!

    Jan 27, 2009 | 2002 Chevrolet Silverado 2500HD

    Not finding what you are looking for?
    2006 Chevrolet Silverado Logo

    Related Topics:

    192 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...