Question about 2005 Chrysler Pacifica

1 Answer

Where is the knock sensor located on a chrysler pacifica 3.5 liter engine.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 47 Answers

Lower driver side of the block if i am not mistaken

Posted on Sep 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the cam sensor inn a2005 chysler pacifica, i can't find it

This video may help ... it covers both the crankshaft sensor location (driver side of engine toward the firewall) and camshaft sensor (passenger side)
2005 Chrysler Pacifica crankshaft camshaft sensor location


Jan 23, 2018 | Cars & Trucks

1 Answer

Where are the spark plugs on an 2006 Chrysler Pacifica 3.5 liter

The spark plugs are located on the "back side" of the engine. To get to them (i.e., for plug replacement) is quite the ordeal -- requiring removal of a bunch of stuff.

I had the dealer do my plug replacement and it was a little spendy -- mostly b/c of all the labor involved.

Mar 07, 2015 | 2006 Chrysler Pacifica

1 Answer

Where is the location of the thermostat in a 2005 3.8 liter chrysler pacifica

Open the hood look the where the top hose from the the raidator inters the engine from the radiator. That is where it is located just below the connection. Should only 2 bolts and maybe 1 more hose or a themostat sensor. Remove the hose, locate the bolts remove any other. pull off, Clean all of the old gasket off. The thermostat should come with a new gasket. Place a small amount of blue sealant to both sides and reconnect in reverse order. Be sure not to over tighten

Dec 12, 2014 | Chrysler Cars & Trucks

2 Answers

Knock sensor diagram

On the 2.4 liter four-cylinder engine it is located on the siie of the engine block (the side nearest the firewall).

On the 3.0 Liter V-6 engine there are 2 knock sensors and the are located in the "valley" below the intake manifold. You'll have to remove the intake manifold to get to them.

Jul 22, 2014 | 2003 Toyota Camry

2 Answers

Where is the map sensor located on the pacifica

The MAP sensor on the Chrysler Conquest is located either on the passenger side or the driver side down around knee level. The Manifold Absolute Pressure sensor (MAP sensor) is one of the sensors used in an internal combustion engine's electronic control system.-------------------------------------------------------------------------------------
Car Key Programmers

Nov 27, 2012 | 2004 Chrysler Pacifica

1 Answer

Where is knock sensor on bank 2 on 2.0 neon

There is just one bank of cyinder since thjis is afour banger. the knock sensor is located at the rear of the engine about middle of the block.

Jun 19, 2012 | 2006 Chrysler Pacifica

2 Answers

I have a 2004 Chrysler Pacifica

136266353that would be your HO2 sensor. It's located in the left hand exhaust manifold closer to the top of the engine. It usually takes a special socket to remove one. If you have any doubt, take it to a shop and have them replace it for you. This sensor effects fuel and driveability, don't go to long without fixing it as it may cause damage to your catalytic convertors.

May 31, 2010 | 2004 Chrysler Pacifica

1 Answer

Positive ventilation crank case valve location

I have one of these cars too, also 3.5. I purchased with 34K and has used a quart of oil every 1000 miles since then. It has no leaks or smoke or any other signs of oil consumption. So much research, nobody knows why these engines do this, some have gone as far as contacting Chrysler just for them to say, " that's normal". But here is the diagram for the PCV:


Nov 11, 2009 | 2006 Chrysler Pacifica

3 Answers

Crankshaft position sensor location on 2004 chrystler pacifica

can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

May 02, 2009 | Chrysler Pacifica Cars & Trucks

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

Related Topics:

688 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides