Question about 2000 Mazda 626

1 Answer

Do I need to remove the tranny to replace the oring on the reverse gear???

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,004 Answers

Yes you need to remove the tranny.

Good luck.

Posted on Sep 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Problems selectin gear in 2009 Holden tk barina it wont go into some gears try puttin it into 1st wont go in then try puttin it in reverse it gos in then lets me go into 1st after selectin reverse 1st

indications are clutch problems
possible clutch cable needs adjusting or replacing
the indications are that the clutch plate is dragging slightly and the gears ore not lining up to mesh until you select reverse or first to stop the shaft turning
If hydraulic system , air in the system and it needs bleeding

Jan 27, 2018 | Holden Cars & Trucks

1 Answer

I have a 1997 astro van it doesnt want to cacth the gear to go reverse all other gears work except reverse do i need a trans mission rebuitl or do i need a reverse gear???? please help money is tigth can...

Odds are yes you need a transmission, reverse is usually the first gear to go out, There is a chance that you could replace the tranny flouid and filter and may help. Thats up to you , this would cost around $60 , A rebuilt tranny could run you around $800 at least depending where you are located. A used one at a salvage may run you around $ 150-$250, And cost at least $200 for labor to replace.
Sorry wish could give you better news, Good luck to you.

Mar 31, 2011 | 1999 Chevrolet Astro

1 Answer

My 2001 audi a4 2.8 tranny hesitates revers, third and fourth

This sounds to be the orings in the solenoid package. Nobody just replaces the orings. Put some tranX in the transmission, this is a oring reconditioner, it costs about $10.00 to15. .
My transmission was dropping out of gear and I used this and with three days it quit slipping. thats been almost two years ago.

Nov 10, 2010 | 2001 Audi A4

2 Answers

Reverse Gear does not work, Can this be repaired ? or replaced? So I do not use reverse.

This is very common, the reverse gears blows out, the reverse gear and some bushings need replacing, many trany shops wont do it, they rather sell you another trany, we had a retired vw tech that would repair them for us all you did was remove the trany, but anyway it can be repaired the parts cost about 150.00 then the rest is labor,

Sep 18, 2010 | 2003 Volkswagen Jetta TDI

1 Answer

Transmission problem

bad oring on the reverse gear

Sep 26, 2009 | 2000 Mazda 626

2 Answers

Transmision wont back up

you need a different tranny because the reverse is a direct gear and is doent engage,the reverse doest work with the drive gear system,so you have a internal mechanical problem in you tranny

Sep 24, 2009 | 2001 Ford Windstar

1 Answer

2000 diamonte tranny stuck in second gear and flashing drive light

Look under dash in the center area behind the ac controller. See if there is green coolant residue in there. Heater Orings regularly leak onto transmission power switching relay, disabling the transmission computer, causing vehicle to lock into safe mode.

Repair requires removing dash to access orings and replace.
You will also need to replace your Auto trans power switching relay.

Sep 10, 2009 | 1991 Yugo Cabrio

1 Answer

My Chevy Express 3500 can't engage the reverse gear. What can be the problem.

reverse drum in tranny broke remove tranny remove torque converter then pump then under that is reverse drum the ring on end breaks off put new drum in and pump gaskets and reinstall

Jul 09, 2009 | 1999 Chevrolet 3500

2 Answers

92 blazer no reverse, other gears are fine,140k

You need to check if the gear oil is still o.k. and the oil transmission and check the release bearing if still intact.

Jun 16, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
2000 Mazda 626 Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides