Question about Chevrolet S 10

1 Answer

Back passengers side drum break get hot what to do.?

Posted by on

  • Poncherello May 11, 2010

    When you say hot, do you mean that the pads are not releasing from the rotor when you let off the pedal?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 811 Answers

Raise vehicle , see if tire spins freely if not, loosen brakes slightly, access it from small opening in inside of brake plate, remove rubber grommet , and turn star nut with screw driver until free, have breaks serviced if not, might also try bleeding brakes

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 durango battery drains check gauge light on


I got a 03 gmc Sonoma 4x4 I replaced the wheel bearings on the rear end now on the passenger side the drum is getting hot really hot so I changed the calipers on both sides still getting hot on that one side what do I do

Jun 14, 2013 | Cars & Trucks

1 Answer

Rear brake on passenger side getting wheel hot, GMC Sonoma


I have a 2003 gmc Sonoma ZR5 4x4 the wheel bearing went out on the passenger side I replaced both bearings when I got it back together the brum on that side was getting hit I replacer the caliper on both sides an its still getting hot only on that side what could it be

Sep 03, 2012 | Oldsmobile Cars & Trucks

1 Answer

Driver's side heat doesn't work


There is a problem with the drivers side air mix valve. I have seen several problems with these. Sometimes the air mix valve (door) gets stuck and when you try to change it the air mix valve link can pop loose, or sometimes it breaks. Sometimes it also breaks the bellcrank on the door itself. The programmer unit can also be defective. Please refer to the picture below. The thing to do is to remove the lower hush panel and possibly the glove box assembly so you can get a good look at what is going on. Then switch the driver's temperature control from hot to cold and back again to observe the movement of the programmer actuator, the mix valve link, etc. to determine where the malfunction is.

11_14_2011_7_01_04_am.gif

Nov 14, 2011 | 1996 Buick Park Avenue

1 Answer

I was checking back brakes, emergency brakes. The axel on the passenger rear is welded to drum. Why wouldyou do that. Cannnot put check back brakes or install new emergency brakes on back passenger side....


They wouldn't and couldn't, or the rear drum would not turn and the car would not move. You need a special fork tool to go behind the drum and adjust the star fitting in order to release the drum and then you will be able to check the linings and cable.

Jul 30, 2011 | 1989 Ford Mustang

1 Answer

I have a 98 dodge durango 4wheel drive 5.2 v8.. breaks are getting hot and wearing out the rear pads. rear have drum front have disk. all 4wheels are getting hot. new everything all the way around.pads,...


check the abs fuse to see if it as blown they system may just be putting more pressure on different parts at differnt times because it is not getting proper control, also if the breaks are new you might consider using a dab of break cement on the back side of the pads and shoes to allow for proper release from the drums/rotors.

Jun 30, 2011 | 1999 Dodge Durango

1 Answer

Hot on driver side and cold on passenger side


If this vehicle has the dual climate controls then the passenger side temperature blend door actuator motor may be bad. The plastic drive gears are prone to breaking and can't move the temp blend door when commanded to do so. I've also seen some controllers go bad but see many more bad actuators.

Nov 12, 2010 | Buick Regal Cars & Trucks

1 Answer

Changed the rear Brakes in my 1992 Ford F-150 2 wheel drive Pickup. On the passenger side rear with the adjuster all the way in, the drum was still difficult to put back on. Put it on anyway and went for a...


Pull both drums and VERY CAREFULLY compare the left and right side, check all the hardware and return springs, position of the shoes, etc. (You know that the left and right are mirror images of each other, as you look at each assembly, think "front vs. rear" not "right vs. left"
Are the shoes pulled tight against the adjuster and the top post? Check to see that the shoes are resting on the backing plates at the correct points, especially near the bottom.
Make sure the shoes are the correct size and have the same mounting points as the old shoes.

Something is wrong. While you may not feel it sticking or grabbing, the excessive heat will cause trouble, including possibly causing the outer wheel bearing to fail.

You must get this fixed, if you cannot resolve the problem, take it to someone who can. Do not ignore this and hope it will correct itself. It won't.

Aug 23, 2010 | 1992 Ford F150 SuperCab

1 Answer

Where is the brake relay on a peugeot 307 hdi?


follow the rod of break padal. It goes to passenger side and if you look underneath the dashboard on passenger side you can find it attached to this rod (the main master cylinder is on passenger side and the rod joins on this side with the drum).

May 03, 2010 | 2005 Peugeot 405

1 Answer

Rear brakes 2000 ford focus zts


emergancy brake cable is froze holding the brake on

Mar 20, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...