Question about 2006 Chrysler 300

1 Answer

MY CHECK ENGINE LIGHT IS ON AND I CANT FIX IT THEY SAY FUSES BUT THERE AL GOOD HELP PLZ

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,004 Answers

Please remove the battery connectors for 5 minutes and replace back. This should turn the check engine light off but you might still take the car for a scan later.

Cheers.

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Mitsubishi diamante L's 2001 check engine light is on but it starts and I can put it in drive but it won't move!!!!!plz help


Light is on because the transmission is dead. Check the transmission fluid and fuses to start. Have the codes read.

Mar 13, 2015 | Mitsubishi Cars & Trucks

Tip

Buy and use a test light


A test light is invaluable to check for battery power, grounds, fuses, bulbs ect. Buy a good one and learn how to use it. For fuses, use the tip and touch it on each end, if both ends have power you now know that ONE, the fuse has power to it and TWO, the fuse is good. You can now check fuses without wasting time pulling and looking. Use a test light to check for grounds. put the wire clip to the positive post of the battery and touch the body or engine and check for light, light is good. Now to check if you negative cable (ground) is good, clip your wire to the negative terminal and touch the engine, any light is bad, check it while trying to start the engine. (a friend can help) if the light comes on, you have a bad ground. You can also use it to check your trailer plug, wiring and grounds.

on Jan 23, 2010 | Ford F Cars & Trucks

1 Answer

Gsw105 gen set runs 150 second then shutdown, i changed already all filters,water, fuel pump is good, problem still occur, error F AL, what solution can i do please?


first did you check alternater output if you havent do that first second check fuses to the alternatorif you dont have at least 13.5 volts need to change the alternator if alternater voltage is ok check ampreage reading with an amp probe

Jan 27, 2013 | Cars & Trucks

2 Answers

My dashboard is dead and no signal comes on. Can I get an electronic map in order to repair this problem?


I would first check all pertaining fuses and make sure you check the ones under the rear seat.

Jan 03, 2011 | 1996 Mercedes-Benz C-Class

1 Answer

I have a 2002 Dodge Durango, w/96,000- miles.. I bought it a yr ago used..anyway, I just had to get a magnetic pick up part put in because it wouldn't start - check enging light had been on - it DOES have...


P0201 is a cylinder 1 injector circuit malfunction. p0301 is cylinder 1 misfire. The first thing to do is check to see that the fuel injector wire is connected good. One would think the injector problem caused the misfire in the same cylinder, Not always the case, It could be the other way around. Since it has the original plugs, I would change them before Thursday.Double check all the spark plug wires for damage and make sure they are connected good at both ends.With any luck this will fix the misfire and you won't have to have it towed.Good luck and let me know if any of this helps.

Dec 28, 2010 | Dodge Durango Cars & Trucks

3 Answers

Check engine light is on, error code is P0171.


Check the MAFS (sensor connected to air intake) and check the hoses under your hood to see if any are broken as this will be the cheapest to fix..


If all the hoses are good, then you should have your O2 Sensor checked as that is the most likely culprit

Aug 17, 2009 | 2008 Volkswagen Passat Sedan

1 Answer

My 1996 cutlas ceirra v6 runs, but no lights work


sounds like a body fuse or lighter fuse. Check fuses with a test light

Mar 29, 2009 | 1996 Oldsmobile Cutlass Ciera

1 Answer

Lights on dashboard 2002alero GL


fuse box should have indications to all fuses if fuses r fine check underneath the hood...if they r all good could b just light bulbs or shortage in wiring which goes under the dash

Dec 17, 2008 | 2002 Oldsmobile Alero

1 Answer

Electrical Problem


Check you battery with a volt guage to make sure you still have good voltage. Check the negative and positive cables and ends to make sure you have a good ground at the engine, chassis, and battery. Check your relay center under the hood and make sure all your fuses are good.

Sep 23, 2008 | 1998 Jeep Cherokee

Not finding what you are looking for?
2006 Chrysler 300 Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...