Question about 2004 Jeep Grand Cherokee

1 Answer

P0121 I changed the oxygen sensors today and take the jeep to test drive. when i get the hill car shaked and get the engine light on. my reader told me that error code P0121, do you suggest to change the throttle sensor?

Posted by on

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,004 Answers

Yes P0121 means Throttle Position Sensor/ Switch A Circuit Range/ Performance Proble.

Please go ahead and replace the Throttle sensor.

That should get the car back in shape.

Good luck and remember to rate this solution.

Also feel free to reach me on onifadeadewunmi@hotmail.com

Murphybanton

Posted on Sep 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a jeep cherokee limited and sometimes when I got to start it, it shakes a little and then I get a burnt smell from the engine


check that the smell is not from the o2sensor wires burning on the exhaust system. This will also give other problem indications.

Mar 28, 2014 | Jeep Cherokee Cars & Trucks

2 Answers

I have a 1998 Jeep cherokee sport. Was driving today and it died. Now there is no spark and no power to fuel pump. Changed fuel pump today and it won't run. Recently replaced oxygen sensors too


U need to check the crankshaft position sensor. The fuel pump will only have power for 2 seconds I till it sees a crank signal. It' controls the asd relay which turns on your spark and fuel

Apr 19, 2013 | 1998 Jeep Cherokee

1 Answer

I have a 2004 Jeep grand cherokee straight six. I replaced the TPS sensor & IAC sensor. recently experienced high idle while in park, lack of power, and engine light came on with a code of P0121? ...


Depending on the system, P0121 is Throttle/pedal position sensor/switch A circuit range/ performance problem.

Did the TPS have slotted mounting holes? If so it may need to be adjusted.

Sep 04, 2011 | 1996 Jeep Grand Cherokee

1 Answer

2008 Jeep Commander with 5.8l Hemi problems with instrument panel


Have shop run an OHM test on your transmission sensors -- then have them replaced and rerun the OHM test. -- it's more than likely an input speed sensor that is not working properly and telling the jeep to go into "limp mode" hence your speed isn't changing but it can't read the actual speed.

Apr 13, 2010 | 2006 Jeep Commander

1 Answer

Today my 95 jeep cherokee shut off while i was driving i replaced fuel filter and it turned on but when i take off to drive it cuts back off


If it idles normally, (normal rpm and not shaking) I'd check the map sensor, throttle position sensor and coil output. I would also check fuel pump output (pressure and actual delivery) Depending upon if the filter you removed was plugged up or not, you may want to consider checking the "sock" filter in the tank as well. You can find fairly decent test procedures in any chilton or haynes manual. Don't start changing anything 'till it has been tested or it can get very expensive with no results. If it is shaking, check cap, rotor wires and vacuum hoses before anything else.

Dec 31, 2009 | 1995 Jeep Cherokee

1 Answer

Engine light came on....code reads oxygen


does the jeep run rough and blow black smoke if so it will be the oxygen sensor if not i would try plugs and a air filter.

Sep 22, 2009 | 1997 Jeep Wrangler

1 Answer

Check engine light comes on after 2 miles of driving


Possible...Check output with a good digital volt/ohm meter. Hot, running, reading should change from between .1v to 1.0v. Take readings with sensor disconnected from the harness, using connector terminal as (+) side of connection and (-) of meter to ground. On multiple wire sensors, they have an internal heating element. this part goes to the two white wires. To test heater, connect ohm meter across both terminals and read resistance. The reading should show same continuity as if you took both meter leads and held them together. Sensor produces very low voltage and therefore any dirt or water in plug connector can throw readings way off. Make sure it is clean and dry.

Apr 05, 2009 | 1994 Jeep Wrangler

1 Answer

Blinking engine light


you might have scraped and destroyed an oxygen sensor on the exhaust..

Oct 27, 2008 | 2003 Volkswagen Jetta TDI

1 Answer

1998 Jeep Wrangler Sport codes P0121 and P0122


did you check voltage to sensors if you need help with proedure, contact me, or you may try patrs houses on line in how to section.

Oct 04, 2008 | 1992 Jeep Wrangler

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...