Question about 2002 Subaru Outback

Open Question

I have 2002 Subaru Legacy Outback. the ABS Light stays on

I have 2002 Subaru Legacy Outback. the ABS Light that stays on. When tested it said it had three bad codes, but only two showed up. Test #9 C0mponent #7 Value 0 Min 311 ECU Id E1.
Test #9 Component #2 Min 72 Measured 0 ECU Id E1.

can you tell me the problem and what these codes mean?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mcgyver468
  • 710 Answers

SOURCE: Cause of noise in front differential of 1997 Subaru Legacy Outback.

there is a plug on the shaft-side of the differential. Using a ratchet remove the plug and with the engine OFF, stick your finger inside the hole and you should get fluid just below the threads of where the plug goes in.

Posted on Apr 24, 2009

Ad
mx5turbo92
  • 545 Answers

SOURCE: i have a subaru legacy outback, abs light comes on

one of your abs sensor is bad or the abs motor,go to local shop to diagnose which sensor,shop usually charge $ 60 to diagnose abs system,good luck, let me know ..

Posted on Jun 04, 2009

  • 199 Answers

SOURCE: what causes pulsating brakes in a 96 subaru

Assuming you are not referring to the pulsation experienced when the anti-lock braking system engages, you should replace the rotors and the pads while you are at it. The days of turning or resurfacing rotors are over. They are cheap.

Posted on Jul 19, 2009

Wolfman304
  • 720 Answers

SOURCE: 1997 subaru legacy outback knock sensor location

Hiya,

Here you go:

2.5L Engine To Remove:

  1. Disconnect the battery ground cable.
  2. Remove the air cleaner housing.
  3. Vehicles with 5-spd transmission: Remove the clutch slave cylinder and set aside.
  4. Disconnect the knock sensor wire harness retainer from the coolant hose.
  5. Disconnect the knock sensor (KS) wire connector.
  6. Remove the mounting bolt and knock sensor from the engine block.
c450de5.gif
Hope this helps...

Cheers,

Posted on Nov 12, 2009

  • 4 Answers

SOURCE: location knock sensor

The knock sensor is located on the top of the engine block almost hidden from view by the intake manifold. It is almost directly below the spot where your throttle cable connects. It will have a bolt running right through the middle of it and a single wire coming out of it.

Posted on May 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My daughter's Subaru legacy outback 2003 when driving home tonight her brake light and battery light and abs light came on and the car was shaking and running rough Now it has to be jumped to run


Hi Bev , if the battery light is on that is probably the whole problem . The battery light on is a indication the charging system is malfunctioning ,not charging . The brake light an ABS are probably linked together , because of low voltage ! The first thing to do is test to see if the alternator is working , hook a voltmeter to the battery . The reading should be 13.1- 14.1 volts if charging ,if only 12.6 it's not charging . If it's not charging you could have a bad alternator , blown fuse's ,wiring problem etc....You could take it by an auto parts store ,if there is one near you . They check these thing's for free ,an be glad to sell you an part !

Aug 18, 2015 | Subaru Cars & Trucks

1 Answer

Why won't my 2010 subaru outback wagon interior lights go off unless it's locked


Check your Interior Light Switch what position is it?

The Striker may have lost a Wire. Test EACH DOOR

Apr 09, 2013 | 1999 Subaru Legacy

1 Answer

Emergency light indicator stay lit on the dashboard of 2002 Subaru legacy


check the brake fluid level first, you might have a slow leak

Dec 02, 2012 | 2002 Subaru Legacy

1 Answer

Antifreeze leaking in my 2003 subaru outback


You must have a shop run a cooling system pressure test with a special tool to determine the origin of the leak. It is likely the problem is the water pump

Jun 08, 2012 | 2002 Subaru Legacy

1 Answer

What years 5speed manual transmissions will fit 2000 subaru outback


all 5spd from legacy legacy gt outback will fit from 96-2002 they have same gear ratio you will have to change over mounts and speed sensor

Jan 14, 2011 | 2000 Subaru Outback

1 Answer

Abs light on check engine light stays on even after changing plugs


computer may need to be reset with scan tool or maybe take neg.battery terminal or sometimes it will take a few good trips to reset itself.

Nov 26, 2010 | 2002 Subaru Outback

2 Answers

Abs light stays on my 99 subaru outback. what should i do to get it off


you have to go to your local garage and have the car computer scanned

this will tell you which wheel sensor is not working properly, or abs module

Feb 17, 2010 | 1999 Subaru Legacy

1 Answer

1998 Subaru Legacy Outback--Rough Idle


I have the same problem!Running on three.I have checked compression,wires,plugs.Changed injecters,plugs.
3 mech.cant figuire it out???

Nov 21, 2009 | 1998 Subaru Legacy

1 Answer

I have a subaru legacy outback, abs light comes on


one of your abs sensor is bad or the abs motor,go to local shop to diagnose which sensor,shop usually charge $ 60 to diagnose abs system,good luck, let me know ..

Jun 04, 2009 | 1996 Subaru Legacy

2 Answers

Abs light on, cruise control and engine light 2007 subaru outback


55 EGR Temperature Sensor or Circuit

ABS light is nothing to do with code 55 separate fault circuits.

Under dash there are two wires with mini spades at the end, connect one of them to the single black multiplug in position 2. Thats RHS plug inlet when you hold plug with tab lock on top.
ABS sensor should then flash up error coded. Ignore code 11 thats a initial flash to let you nknow the difference between a fast and slow flash.

Let me know what code flashes up and I will tell you the symptom,

Dan

Jan 01, 2009 | 2002 Subaru Outback

Not finding what you are looking for?
2002 Subaru Outback Logo

Related Topics:

943 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...