Question about 1987 Chevrolet S-10 Pickup

1 Answer

How do i remove my starter on a 1987 chevy - 1987 Chevrolet S-10 Pickup

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 111 Answers

Two mounting bolts. Two wire terminals. Disconnect battery first for safety. You may need to remove exhaust manifold or something to get at it. The starter is mounted with flat metal shims that adjust how it meshes with the flywheel. Save those and try various positions with your new starter till it doesn't make too much noise when you start.

Posted on Sep 27, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i wire my 1987 chevy R10 starter

the main battery cable goes to the starter solenoid . then a wire from the starter key or switch goes to the small terminal on the solenoid.

Oct 20, 2014 | Cars & Trucks

1 Answer

Replacing 1987 Chevy Nova Thermostat

Look for a hose extending from the top of the radiator to a round housing atop the engine. Removal of the housing cap screws will reveal the thermostat. Note the mounting orientation of the thermostat to avoid installing the replacement upside down. Remove the old thermostat and gasket. You may have to scrape the old gasket off. Place the replacement gasket and thermostat in position and reinstall the housing cap screws and tighten securely. Start your Chevy and check for leaks..

Jan 09, 2014 | 1987 Chevrolet Nova

1 Answer

1987 BMW 735i, I just had the starter changed and now it won't stop cranking

The replacement starter may have required installation of shims to ensure correct engagement with the flywheel and that wasn't done. Also, the replacement starter could have been a look-alike-but-not-function-alike item.

Jan 30, 2018 | 1987 BMW 7 Series

1 Answer


Click here to see how to remove.Here's some new ones.

Dec 22, 2012 | 1986 Chevrolet Celebrity

1 Answer

I hear a clicking sound when I turn my starter on my 1987 chevy s10

1.The battery is dead,use a volt meter to verify,jump or recharge if necessary
2.The connections at the battery and/or starter are bad,clean
3.The starter could be bad,remove,test,replace if indicated
4.Only ran across this once,very remote,engine seized,due to vehicle age,replace vehicle

Jun 23, 2012 | Chevrolet S 10 Cars & Trucks

1 Answer

Can't get the starter out pass the cat on my 1987 corvette as shown in repair manual

My manual (Chilton) says to remove the front starter support bracket and heat shield, loosen the starter bolts and lower the front end of the starter first. It comes out the front not the traditional back way. Hope this helps.

Mar 07, 2012 | 1987 Chevrolet Corvette

1 Answer

How do you take the starter out of a 1987 nissan pathfinder v6?

disconnect the negative cable from the battery, now disconnect the wires on the starter solenoid posts,, remove the two bolts that hold the starter in place ( bottom one first ),, pull starter off.
installing the starter is just the reverse of removal.


Feb 04, 2011 | 1987 Nissan Pathfinder

2 Answers

How do i replace my own starter on my 1987 licoln town car?

1. Raise the car and support it.
2. Disconnect the negative battery cable.
3. Crawl under the car and locate the starter. It is easiest to do this by following the positive power cable from the battery down to the starter.
4. Remove positive cable from starter.
5. Remove wires from solenoid.
6. Remove bolts holding starter to the transmission bell housing.
7. Remove the starter.

Installation is the reverse of removal.

Oct 26, 2010 | 1987 Lincoln Town Car

1 Answer

Where is the fusible link in a 1991 chevy vandura?

the fuseable links are on the starter
remove the starter and remove the main battery feed the other 2-3 wires are the fuseable links

Feb 20, 2010 | 1987 GMC VanDura

1 Answer

How do you remove starter on 1987 Jetta vw? top or underneath?

Support the engine as the bolts go through the front motor mounts, disconnect battery (have radio cde if ness) diconnect starter wres, remov bolts> Install is reverse.

Jul 20, 2009 | 1987 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides