Question about 1994 Chevrolet Silverado 2500

2 Answers

94 Chevy 1500, 5.7 engine. Somestimes when the

94 Chevy 1500, 5.7 engine. Somestimes when the wheels are turned sharp and the A/C is on the serpentine belt jumps-off.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I have also seen this caused by a bad bypass valve in the power steering pump. reaching the end of the steering travel and the pump continues to build pressure with nowhere to go. It causes the pump to bind and slow so the engine turns the belt too fast and slings it off.

Posted on Jan 04, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 546 Answers

Check belt tensioner pulley for worn bearings.check that belt is not worn beyond serviceable length,has cracks or is frayed.

Posted on Sep 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 94 chevy 1500 and the brake lights are dim and wire from brake switch gets hot brake is on then it blows a fuse. traced all wires and replaced brake switch. what else could it be?


Possibly a short in the directional switch in the steering wheel. Your brake lights use the same filament as the turn signals, so the brake light wiring goes thru the directional switch. Does one wire from the brake light switch go up the steering column?

Sep 16, 2010 | 1994 Chevrolet C1500

1 Answer

My 94 chevy 1500 may or may not shift into drive


Is your trany full of fluid ? Has it been leaking at all ? May need a kit

Feb 03, 2010 | 1994 Chevrolet K1500

1 Answer

Can you put a steering column from a 1997 c/k 1500 chevy truck in a 1994 c/k 1500 chevy truck? I am putting the motor (4.3 V6) from a 1997 c/k 1500 chevy truck into a 1994 c/k 1500 chevy truck. I need...


pick up a chilton book from chapters indago and check the diagrams they might be similar but i believe the wiring is a lot different '
it is likely you will need both manules

Jan 08, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

Four wheel drive will not engage on 94 1500 where is the fuse for the actuator


Does you heater fan work? For many years Chevy used the same fuse for the 4 wheel drive actuator as for the heater fan. Which I found rather stupid because, if the actuator shorts out and blows the fuse, now your stuck in a snow bank with no heat.

Dec 10, 2009 | 1994 Chevrolet C1500

1 Answer

94 chevy 1500, 350 engine. putters after start


check your vacuum lines they are weather cracked and leak vacuum air

Oct 07, 2009 | 1994 Chevrolet K1500

1 Answer

94 chevy 1500 will start for about 30 mins. and then just stop


Does it blow black smoke when it's hot? if so, Replace the cold start sensor. If not check to make sure your cats aren't plugged, (they will get red hot). If they are plugged the engine will loose power and stall.

May 29, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Rear end in 1999 chevy 1500 binds on turns


well i had the same problem everyone told me the clutches in the rearend were sticking making it stick in positive traction (only your passanger side rear wheel pulls unless you start spinning then a type of clutch engages the other side so you have traction then when you stop spinning it disengages it should never be engaged if your on pavment) now you can do what i did listen to everyone when they tell you its normal or you can take it to someone with experience now and save yourself some money cause it will start popping then it will get some viberation then next it will break the clutches and when that happens you will have to replace the pinion,ring,and the spider gears as well as the clutches.make sure you have pleanty oil in rearend if you dont add the limited slip conditioner it might free clutches up but if i had it to do over id put it in the shop or stop driving it before i broke something hope this helped

Mar 10, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

417 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...