Question about 1987 Plymouth Horizon

1 Answer

E-brake is stuck on 1987 ply horizon

I know i should be able to pop it loose under the car but i've never had to do it... how do i do it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 6,674 Answers

If you see slack on cable from handle to "Y" where it runs to both rear wheels, then you'll need to get cables at rear wheels loosened up. Do you use hand brake much, and what have you tried so far?

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1987. Right front brake disc is stuck on the sheath around the spindle. How do I break it loose?


If you mean that the rotor is stuck on the hub, it is most likely rust or corrosion, some makers use screws on them. Use a dead blow hammer or rubber mallet on it. Don't use a metal hammer.

Aug 20, 2015 | Subaru Cars & Trucks

1 Answer

How do u disconnect the emergency brake on a 1987 dodge dakota 4x4


It depends on where the cable is stuck.
You can disconnect it at the connection points, you have a front, center, and two rear cables. But if the cable is stuck at one of the brake drums, disconnecting it at the front or center connector won't free up the brake shoes.

Jan 24, 2013 | 1987 Dodge Dakota

1 Answer

Vw cabrio brakes locked up


seeing that we only offer advice we have no way to know cost of a fix , only a brake service shop could give you an estimate after they look at it .

Mar 12, 2017 | 2000 Volkswagen Cabrio

2 Answers

Wont start trying to locate the fuel pump jag. xj6


Hello.
Most cars have the fuel pump on the drivers side right in front of the rear wheel tucked up into the body panel. You can easily find them by tracing the thin fuel line from the tank until you get to the fuel pump. Hope this helps!

Dec 07, 2009 | 1987 Jaguar XJ6

2 Answers

Metal on metal noise and intermittent grinding and popping in right rear. Suspect axle or bearing


Check the brakes before you get into takin g out the axle or bearings neadlessly.If they are alright go for the bearings next.

Nov 02, 2009 | 1987 Porsche 944

1 Answer

E-brake stuck on 87 horizon. how do i release under car?


If handle is down, look for slack in cable under car, and if it's got slack in it, then you'll have to get cables at rear wheels loosened up, going into backing plate.

Sep 26, 2009 | 1990 Plymouth Horizon

1 Answer

My 1989 Plymouth Horizon when I am stopped and holding my foot on the brake pedal I get a low hissing sound from somewhere in the car. I have checked all brake lines ad they are fine as well as master...


That hissing sound you hear is the brake booster, that big black round shaped thing that the brake master cylinder is bolted to, the diaphram inside, probably has a hole in it. Have to replace whole thing, not just the diaphram.

Mar 16, 2009 | 1989 Plymouth Horizon America

1 Answer

1987 Toyota Celica ST half shaft


pull wheel, remove nut on half shaft, calaber, brakes, roader, tie rod, lower control arm, pop out half shaft from knuckle reinsert shaft to tranny and put back together easy looking about an half hour to an hour

Feb 23, 2009 | 1987 Toyota Celica

2 Answers

Don't know where to put brake fluid


First..make sure you have the right fluid..DOT number...the reseerve is on the drivers side under the hood near the back of the motor cavity.....should be made of a very translucent white platic....make absolutely sure nothing falls into the resevoir when you're adding fluid

Jan 03, 2009 | 1987 GMC VanDura

1 Answer

1985 PLy Horizon distributor rotor position


Find the end of the plug wire for cylinder 1. Place the plug wire into the distributor cap. Rotate the Crankshaft until Cylinder #1 is TDC. align the rotor in the distributor cap with plug wire number 1.

Nov 23, 2008 | 1985 Plymouth Horizon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...