Question about 1995 Chrysler Sebring

1 Answer

Where is the rear brake line on the master cylinder

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,111 Answers

The rear brake line is connected to the master cylinder inside the hub ..remove the tire and remove the hub the 2 bolts that hold the master cylinder in place are at top the line going into the cylinder itself is the brake line

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why even with new brake parts in the front and rear on my 2995 Ford f150 2wd truck would front brakes work but not back ? I even put truck on bay lift and hit the brakes and rear just kept spinning.


Bill:

Check your master cylinder. It could be a piece of junk lodged in the fluid port for the rear brake lines, or in the brake line its self. The fact that both rear wheels spin tells me that if it is a clogged line, it is between the two manifolds, (one next to the master cylinder, and the other where the rear brake line splits into two... one for each rear hub. Or it could be that the piston in the master cylinder needs to be replaced. I would disconnect one brake line at one rear wheel and disconnect the rear brake line at the manifold (near the master cylinder)and blow that line out with air pressure. . do not leave the rear brake line connected to the master cylinder as you blow air through the lines as you may damage the master cylinder piston packings. You'll have to bleed the brakes when you are done.

Jan 24, 2016 | Ford Cars & Trucks

2 Answers

Brake lines to master cylinder


What model master cylinder have you installed?

Jun 10, 2008 | 1991 Lincoln Mark VII

2 Answers

Master cylinder diagrams


the on from smaller chamber

Aug 15, 2014 | 1995 Chevrolet Camaro

2 Answers

Replaced some brake line, rear pads and one rear wheel cylinder. Now no pressure and nothing happening when trying to bleed.


Does the car have ABS ? And does it have an equalizer block for the 4 wheels ?
It sounds like the ABS has been affected, or there is an equalizer block that is stuck on the front wheels only.
Can you open the bleeder or the rear line on the master cyl and get fluid to come out by depressing the pedal ?

Jul 07, 2013 | 1997 Mercury Tracer

1 Answer

2001 Silverado 2500 HD Why Rear brakes don't work after I installed new hydro-boost power booster, master cylinder, calipers, and pads. I bled master cylinder before installing, and brakes beginn


Hello Patricia,

Have you checked the master brake cylinder reservoir for brake fluid loss?

I don't suspect the master cylinder as you have replaced it... but am more suspect of a leaking brake line or fitting which should have
been discovered when you had the system bled.

The only time I ever had a rear brake problem with a 2500 series Chevrolet was due to seized rear brake caliper guide pins...as your calipers are also new that is not your problem.

If your brake pedal feels spongy and travels to the floor board you have air in the system, a brake fluid leak or a failure in the power steering system, such as a broken hose, broken power steering pump drive belt, or failed pump, would result in a loss of pressure to both the hydro-boost and steering.

Find more information here:

. Hydro Boost Power Assist Systems Operation Diagnosis and Repair

Jul 23, 2017 | 2001 Chevrolet Silverado 2500HD

1 Answer

Replaced all brake lines, rear wheel cylinders, front calipers. No fluid to rear brakes, no fluid to master cylinder bleeder. Fluid is in front brakes. How to resolve? Thank you


It sounds as though where the rear brake lines meet up with the master cylinder; there is probably a piece of dirt in the lines that could be blocking any fluid from getting in. To test this, I would remove the brake lines from the master cylinder and then remove the master cylinder. Once done, have the master cylinder cleaned inside out. This will remove the dirt particles that are clogging your lines.

Aug 22, 2011 | 1988 GMC C2500

1 Answer

Bleeding the brakes ,But no fluide in the rear brakes


Check the master cylinder, pump up the brakes and crack the line at the master cylinder to the rear brakes, if no pressure and it was ran empty or is new part, bench bleed the master cylinder and recheck for pressure at the master cylinder, if you have pressure follow the brake line to the proportioning valve and crack that line before and after the fitting, good luck.

May 09, 2011 | Suzuki Sidekick Cars & Trucks

1 Answer

How to bleed brakes on 1997 Saturn


The brake system bleeding procedure differs for ABS and non-ABS vehicles. The following procedure pertains only to non-ABS vehicles. For details on bleeding ABS equipped vehicles, refer to the ABS procedures later in this section.

WARNING Make sure the master cylinder contains clean DOT 3 brake fluid at all times during the procedure.
  1. The master cylinder must be bled first if it is suspected of containing air. Bleed the master cylinder as follows:
    1. Position a container under the master cylinder to catch the brake fluid.
    2. Loosen the left front brake line (front upper port) at the master cylinder and allow the fluid to flow from the front port.
    3. Connect the line and tighten to 24 ft. lbs. (32 Nm).
    4. Have an assistant depress the brake pedal slowly one time and hold it down, while you loosen the front line to expel air from the master cylinder. Tighten the line, then release the brake pedal. Repeat until all air is removed from the master cylinder.
    5. Tighten the brake line to 24 ft. lbs. (32 Nm) when finished.
    6. Repeat these steps for the right front brake line (rear upper port) at the master cylinder.
WARNING Do not allow brake fluid to spill on or come in contact with the vehicle' finish, as it will remove the paint. In case of a spill, immediately flush the area with water.
  1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
    1. Right rear
    2. Left front
    3. Left rear
    4. Right front
  2. Bleed the individual calipers or wheel cylinders as follows:
    1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end.
    2. Submerge the other end in a transparent container of brake fluid.
    3. Loosen the bleed screw, then have an assistant apply the brake pedal slowly and hold it down. Close the bleed screw, then release the brake pedal. Repeat the sequence until all air is expelled from the caliper or cylinder.
    4. When finished, tighten the bleed screw to 97 inch lbs. (11 Nm) for the front, or 66 inch lbs. (7.5 Nm) for the rear.
  3. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.
zjlimited_349.jpg

Fig. 1: Loosen the front brake line in order to bleed the master cylinder

zjlimited_350.jpg

Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid

zjlimited_351.jpg

Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system





Hope this helps to solve it; remember to rate this answer.

Dec 29, 2010 | 1997 Saturn SL

1 Answer

Brake line diagram


Brake Lines and Hoses
Double-walled steel line is used in the hydraulic lines between the brake master cylinder and the front tube connector, and between the brake master cylinder and the flexible brake hose at the rear wheels.
Double-flared brake lines provide good leak-proof connections.
When replacing hydraulic brake lines, hoses, or connectors, tighten all connections securely. After replacement, bleed the brake system; refer to Section 206-00 .
The wet appearance of the outer cover of the rubber brake hose is referred to as "sweating." This is a normal condition for neoprene rayon braid hose and is not a sign of leakage or cause for replacement of the hose.

Hydraulic Brake System Components — Non-ABS

dff7165.gif
Item Part Number Description 1 2005 Power Brake Booster 2 2455 Brake Pedal 3 2261 Rear Wheel Cylinder 4 2552 Rear Disc Brake Caliper— (Mexico Only) 5 2B120 Disc Brake Caliper—, Front 6 2B091 Brake Pressure Control Valves 7 2140 Brake Master Cylinder

May 02, 2009 | 1998 Mercury Tracer

Not finding what you are looking for?
1995 Chrysler Sebring Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...