Question about 2009 Pontiac Vibe

Open Question

How do I program the keyless remote on a 2009 Pontiac Vibe so the horn chirps when locking the vehicle

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: Programming a 2006 Pontiac Gran Prix Keyless remote

The rke on 06 pontiac only can be programed using a diagnostic scan tool or Tech 2.
Conect the scan tool to the vehicle. turn key to on position.
Select 1 body, 2 them select special funtions
3 slect program key fob,
4 select the number of key fob you want to program.
5 Press and hold the lock and unlock key simultaneous. about 15 seconds
The power lock cycle confirm the remote is programed.

Posted on Jul 03, 2008

inf12
  • 13 Answers

SOURCE: keyless remote programming insyructions

95 bonny--1-turn ign switch off 2a75c3b.jpg 2-using a fused jumper wire jumper data link connector #8 blk/wht wire to #4 blk wire (look under dash for dlc)
3-press unlock button on 1 transmitter doors should lock and unlock
4-repeat step 3 if doing more than 1 remote
5-remove fused jumper

36a8224.jpgfor the 1993 car same way except jumper term a blk/wht
term g ppl/wht
have fun

Posted on Feb 08, 2009

  • 21 Answers

SOURCE: How do you program a

Using a fused jumper short between terminal G and terminal A on the ALDL plug. The receiver will then cycle the door locks within one to three seconds this is saying that the reciever is in program mode. Press any button on the remote once the locks should cycle  to acknowledge the transmission has been received. Thats it      remove the fused jumper lead. you have now finished programming the receiver. Enjoy

Posted on Apr 23, 2009

  • 401 Answers

SOURCE: Pontiac G6 unlock button on

Hi you would have to take your vehicle to a dealer or shop most likely buy a new remote thenit will need to get programed that's were the shop or dealer comes in

in the meantime try LOCKING THE CAR WITHOUT USING THE REMOTE then unlock with the key the horn should not go off

works on most GM vehicles

Posted on May 06, 2009

  • 2 Answers

SOURCE: How to program a keyless remote for a Pontiac

that part # is wrong, that part number is for chev pickups etc. the correct # is 25678792 for 97-99 bonneville and works for some others too!

Posted on Sep 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Ford 2010 Ford Explorer "Remote Keyless Entry (RKE) module" located


The RKE is controlled by the SJB - smart junction box ! Fords BCM - body control module .
Principles of Operation
Power Locks
The SJB controls the power lock/unlock feature of all of the vehicle doors, including the liftgate, to lock or unlock based on the input received from the door lock control switch, the keyless entry keypad or the remote keyless entry (RKE) transmitter. Power locking and unlocking of the doors function independently of the key position, vehicle speed or transmission position. The smart junction box (SJB) activates internal relays to supply the correct voltage and grounds for the door lock actuators.

Your best bet would be to take to ford dealer or some other qualified repair shop .
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Unlock
The RKE transmitter feature provides lock/unlock functions independently of key position, vehicle speed, or transmission position. The RKE transmitter feature provides a 2-step process for unlocking the doors. Upon receipt of the first request for unlocking the doors, the RKE control feature requests the SJB to unlock the driver door only. If another unlock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB to unlock all the doors. This feature can be changed to global unlock, so that all the doors unlock on the first press of the unlock button. To toggle between the 2-step unlock and the global unlock press the lock and the unlock button on the RKE transmitter at the same time and hold the buttons for 4 seconds. The turn signal lamps flash to confirm that the feature has been toggled.
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Lock
The RKE transmitter feature requests that all the doors be locked when the lock button is pressed. On any press of the lock button with all doors closed, the SJB provides 1 flash of the parking lamps. If any door is ajar, no flash occurs. As soon as the last door is closed, the SJB provides the flash of the parking lamps. If 2 presses of the lock button are received within 3 seconds, the horn chirps once, and the parking lamps flash twice to indicate that all the doors are closed and locked. If any door is ajar when the second lock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB chirp the horn twice without flashing the parking lamps to indicate it locked all the doors but 1 or more doors are ajar. When the key is in the ON or START position, the parking lamp flashes and horn chirp confirmations do not occur.

All locks not working ?????
  • The doors do not lock/unlock using the remote keyless entry (RKE) transmitter
  • RKE transmitter battery
  • RKE transmitter
  • RKE transmitter programming
  • Aftermarket system
  • SJB
  • Go To Pinpoint Test H .

Apr 16, 2017 | Ford Cars & Trucks

2 Answers

2003 Yukon xl horn problem


The vehicle horns are activated under the following conditions:
?€¢
The horn switch is depressed.


?€¢
The body control module (BCM) commands the horns on. The BCM commands the horns on under either of the following conditions:


-
When the content theft deterrent system detects a vehicle intrusion. For further information, refer to Content Theft Deterrent (CTD) Description and Operation in Theft Deterrent.


-
When the panic button is depressed on the remote control door lock transmitter. For further information, refer to Keyless Entry System Description and Operation in Keyless Entry.


-
When the OnStar?® system is used to sound the horns, if equipped. For further information, refer to OnStar Description and Operation in Cellular Communications.


-
When the keyless entry system is used to lock the vehicle, a horn chirp may sound to notify the driver that the vehicle has been locked. The notification feature may be enabled or disabled through personalization. For further information, refer to Keyless Entry System Description and Operation in Keyless Entry

Jun 22, 2016 | 2003 GMC Yukon XL 1500 SLT

1 Answer

I have a 2003 Checy Malibu and the horn will not work when I hit the steering wheel.


System Description
The horn system consists of the following components:
?€¢
HORN fuse


?€¢
Horn relay


?€¢
Horn slip ring


?€¢
Horn switch


?€¢
Horn assembly


?€¢
Body Control Module (BCM)

System Operation
The vehicle horn system is activated under the following conditions:
?€¢
The horn switch is depressed.


?€¢
The body control module (BCM) commands the horns on. The BCM commands the horns on under any of the following conditions:


-
When the panic button is depressed on the remote control door lock transmitter. For further information refer to
Keyless Entry System Description and Operation .


-
When the keyless entry system is used to lock the vehicle, a horn chirp may sound to notify the driver that the vehicle has been locked. The notification feature may be enabled or disabled through personalization. For further information refer to Keyless Entry System Description and Operation .

May 18, 2016 | Cars & Trucks

1 Answer

09 vibe key fob door lock sound activation


there should be an info center on your car and it ask all the questions in you want the light on and how long horn or no horn valet lights or not

Sep 22, 2012 | 2009 Pontiac Vibe

1 Answer

I have a 2000 pontiac trans am. when i set my alarm my haedlight pop up. they never use to. replaced module,and headlight motors,still didn't fix it.


In your owners manual on pages 2-19 and 2-21 tells you how to change this.

Entering Programming Mode
1. Turn the ignition key to RUN, then to OFF. This will
disarm the content theft-deterrent/alarm system
(if equipped).
2. Remove the RADIO fuse. This fuse is located in the
main fuse block which is located on the left side of
your instrument panel. The radio fuse is on the lower
right-hand corner of your instrument panel. See
"Fuses and Circuit Breakers" in the Index.
3. Turn the ignition key from OFF to RUN three times
quickly (within five seconds). The vehicle will
respond by locking the doors, unlocking the driver's
door and releasing the hatch. Your transmitter is now
ready to match the vehicle. Leave the ignition
in RUN.
4. Press and hold the LOCK and UNLOCK buttons on
the first transmitter for 15 seconds. The vehicle will
respond as in Step 3.
5. Repeat Step 4 for the remaining transmitters.
6. When you have finished matching all of your
transmitters, replace the RADIO fuse.
7. Check that all transmitters work by pressing
the buttons.

Programmable Modes
Your vehicle can be programmed to one of the
following modes:
Mode 1: All Off (The headlamps will not flash and the
horn will not sound to provide you feedback that a
lock/unlock command has been received by the remote
keyless entry transmitter.)
Mode 2: Horn and Lamps/Lamps (Your horn will sound
briefly and your parking lamps will flash when you
press LOCK on the remote keyless entry transmitter.
Only your parking lamps will flash when you press
UNLOCK.)
Mode 3: Horn and Lamps (Your horn will sound briefly
and your parking lamps will flash every time you push
LOCK or UNLOCK.)
Mode 4: Lamps (Your parking lamps will flash every
time you press LOCK or UNLOCK.)
Mode 5: Lamps/Horn and Lamps/Lamps (Your lamps
will flash upon the first press on LOCK, your lamps will
flash and your horn will sound upon the second press
on LOCK and your lamps will flash upon any press
on UNLOCK.)
Vehicles are delivered programmed in Mode 5.
To change the mode, do the following:
1. Press the UNLOCK button on the remote keyless
entry transmitter.
2. Count the number of chimes you hear. The number
of chimes tells you which mode your vehicle is
set for.
3. Press the UNLOCK button, again, on the remote
keyless entry transmitter until you hear the number
of chimes that correspond to the mode selection
you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

When programming is complete, turn the ignition to
OFF and reinstall the RADIO fuse.

Sep 20, 2010 | 2000 Pontiac Firebird

2 Answers

Program gm key fob


There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. SEE THE DEALER.

Nov 09, 2009 | 2009 Pontiac G6

1 Answer

2009 Pontiac Vibe doors locking on their own


Keep the locking remote far away from the vehicle and see if it still locks on it's own.
Also you may need a new battery in the remote or a new remote.

May 22, 2017 | 2007 Pontiac Vibe

2 Answers

Keyless entry wont work after battery died


stand at the vehicle and push and hold the lock and unlock buttons till the horn chirps to resync the key fob

May 03, 2009 | 2002 Pontiac Sunfire

2 Answers

1999 lincoln con


SECTION 501-14B: Keyless Entry/Computer Operated Locks 1999 Town Car Workshop Manual GENERAL PROCEDURES Programming —Keyless Entry Keypad Code
  1. Enter the permanent factory keyless entry keypad code.
  1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.
  1. Enter the new five-digit keyless entry keypad code.
  1. To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.
  1. If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.
  1. After all new keyless entry codes are programmed:
    • Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
    • Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
    • -------------------------------------------------------------
Programming —Transmitter
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------
Programming —Remote Memory Activation NOTE: This procedure must be completed within 5 seconds.
  1. Press the SET button on the driver door panel.
  1. Press any button on the keyless entry remote transmitter to be associated with a memory setting.
  1. Press the 1 or 2 memory button on the driver door panel.
-------------------------------------------------------------
Programming —Autolock and Horn Chirp
  1. NOTE: This procedure must be completed within 30 seconds.
    Turn the ignition switch to RUN.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to OFF.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.
  1. Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.
  1. Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.
----------------------------------------------------------------------------------

Apr 07, 2009 | 1999 Lincoln Town Car

1 Answer

Programming new keyless entry remote


Yes...

1) Remove the "MALL PGM" fuse located in the glove compartment (see owners manul for location)

2) Turn ignition switch to "Accessory" then "Off" then back to "Accessory" witin 1 second. (accessory is opposite the forward direction key is normally turned for starting the vehicle)

3) Plug in drivers side seat belt.

4) Open and close a door (will hear a chime indicating in program mode.)

5) Press and hold both the "Lock" and "Unlock" buttons on the Fob and wait at least 7 seconds (may take longer) you'll hear a chirp or the horn will sound.

6) repeat step 5 for all other Fobs.

7) turn key to Off and replace fuse.

Jun 13, 2008 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
2009 Pontiac Vibe Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...