Question about 2000 Chrysler Cirrus

1 Answer

How do you install an oxygen sensor on a 2000 chrysler cirrus?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

Go to your local Auto Zone and they will show you which one needs replacement by reading a code reader that plugs into your car dignostic port. You then buy the right one from them cheaper than the Dealer and they will lend you the removal tool to take it off.

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does a shaft speed sencer do for a 2000 cirrus


According to Stratusphere.net, "Symptom: The car won't shift out of 1st gear. The 'Check Engine' light is on.

The speedometer doesn't work for this one. You're only able to go about 30 MPH without going above 4000 RPM.

Likely Cause #1: The Output Shaft Speed Sensor went bad.
Likely Solution #1: Replace the sensor (Part #4800879)."

The good news is that they are relatively cheap if you can install them yourself.

Apr 03, 2015 | 2000 Chrysler Cirrus

1 Answer

1999 Cirrus battery loses charge when car sets.


Here is a neat trick for that problem (my 1999 Cirrus drain issue could not be solved) Disconnect the negative cable for a minimum of 5 seconds, then reattach it. Doing this before you go to bed insures a charged battery in the morning. It is when the engine is turned over that the battery drain begins again (probably the anti-lock brake motor) Try not to perform this too often, as it will mess with the oxygen sensors over time, which reset their data from the power disconnect. Oxygen sensors in this car gather their needed data from about 40 miles of regular driving, and it is recommended to drive the car often to engage these sensors occasionally. The car might drive slightly rougher after the battery disconnect because these sensors are not fully activated. They determine crucial fuel / oxygen ratios to deliver to the engine and its components...

Feb 16, 2013 | 1999 Chrysler Cirrus

1 Answer

Replace oxygen sensor


oxygen sensor is located in the exhaust pipe just as it leaves the engine, it monitors the exhaust gas as it exits the engine, look down between the back of engine and the firewall. peek-a-boo ! some cars have (2) one @ the exh. pipe before the CATalitc converter. use a 7/8 " wrench, wd 40 will help also. tight is tight too tight is broke.

Jan 15, 2013 | 2000 Chrysler Cirrus

1 Answer

Does anyone know how to replace a oxygen sensor ?


Yeah it is on the exhaust you have two of them. Just replace both. You need a O2 sensor socket and will have to pull exhaust down to get to them. You might be able to reach the top one. There is two. I would do both

Jun 02, 2012 | 2000 Chrysler Cirrus

1 Answer

Where is the distributor cap in my 2000 chrysler cirrus 2.5l V6


On the rear face of the right cylinder head. Cam sensor is built into it too. Just follow a plug wire.

May 03, 2012 | 2000 Chrysler Cirrus

1 Answer

How long do i run my 2000 chrysler cirrus 2.4 liter till the evap sensor is ready for emissions


most cars u can drive around 100 miles park the car then drive it to the shop the next day and be ok

Mar 14, 2010 | 2000 Chrysler Cirrus

1 Answer

2000 Chryler Cirrus - engine races all the time


Either the throttle body is being held open by something or the idle control valve is stuck open. Check where the throttle cable hooks to the throttle body, make sure the cable is not caught on something.

Jan 10, 2010 | 2000 Chrysler Cirrus

1 Answer

2000 chrysler cirrus wont shift


it is going into limp mode. You need to take it to a trans shop to have diagnostic

Jul 06, 2009 | 2000 Chrysler Cirrus

Not finding what you are looking for?
2000 Chrysler Cirrus Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...