Question about 1990 Chevrolet S 10 4WD

Open Question

Need a help with door linkage the inside handle 1989 chevy s10

Need a help with door linkage the inside handle has no spring action wher is the spring that works this and when I roll the window down it hangs up or catahes on the linkage know it wiil not open from the outside also how do i remove the window crank haneed a help with door linkage the inside handle has no spring action wher is the spring that works this and when I roll the window down it hangs up or catahes on the linkage know it wiil not open from the outside also how do i remove the window crank handle thanksndle thanks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My passagner door will not open either way inside


If you have the linkage there and it is working, Then the latch is broke. Replace it.

Oct 19, 2014 | 1993 Chevrolet S-10

1 Answer

2009 ford fusion left ft door wont open from inside power lock works must roll down window to open with outside handle


Either the linkage connected to the handle has come off, or the piece on the handle inside has broken. You will need to remove the panel from the door and repair or replace the handle.

Mar 28, 2014 | 2009 Ford Fusion

1 Answer

2000 Chevy S10 passeger door won't open


Remove the door panel and inspect the latch rods for damage or broken retention clips. A video is below of how to remove the panel.

Nov 06, 2012 | 2000 Chevrolet S-10

1 Answer

1989 chevy cavalier - somehow safety door lock engaged and now I can't close the driver door. How do I unlock it?


  1. This is what probably occured
  2. While the door was open the latch on the door was closed
  3. If the spring inside the latch is broken, Working the inner or outer door release handles will not open the latch.
  4. place a screwdriver in the opening of the latch where the door striker would be if the door was closed.
  5. apply pressure to the latch paw while operating door release.
  6. latch should open.
  7. replacement of the latch will keep this from happening again

Sep 07, 2010 | 1989 Chevrolet Cavalier

1 Answer

Third door 2002 s10 will not open replaced broken handle top latch will release but not bottom latch


The handle you replaced is a dual action. It should have two linkage arms. 1 coming down from the top & one coming up from the bottom. Sometimes the little plastic keepers that the rods snap into that hold them on to the handle become worn out. Hopefully replace the lower keeper. They may look ok, but it is a very small tolerance.

Sep 05, 2010 | 2002 Chevrolet S-10

1 Answer

2007 chevy tahoe driver side door handle will not open door


the linkage behind the handle either the retaining clip broke or popped off need to remove the door panel to check and fix

Mar 13, 2010 | Chevrolet Tahoe Cars & Trucks

3 Answers

How to replace the exterior door handle,both sides,on a 1992 Chevy S10 pick up. Is there an on line illustrated manual I can download or copy? I will need step by step instructions. Illustrated step by...


remove seat belt bolts and pull it out. the rest is just held in with tabs.

..or if you want Forget taking the door apart - just remove the two bolts holding the latch assembly to the door - Pull the latch assembly out far enough to see the pin that goes through the broken handle - drive the pin out far enough to remove the handle - insert new handle that you just removed from the replacement latch assembly - drive pin back in - Throw the rest of the replacement kit away since all that was broken was a tab on the handle you just replaced.

hope this helps a lot. :)

Feb 13, 2010 | 1992 Chevrolet S-10

1 Answer

Drivers Side Door Handle


You need to take inside door panel off This just clips on but there are screws in armrest and inside door handle look for any other small square covers that may hide screws Lift panel up Make sure window is up Disconnect wiring from panel and you can now get at door handle linkage and bolts

Jul 10, 2009 | 1989 GMC S-15 Jimmy

1 Answer

How to replace inside door handle on passenger on 1998 chevy silv


Remove screw from inside door grab handle. Remove door panel by carefully prying out plastic clips. Drill or chisel off pop rivets holding the handle on. Pull handle out far enough to disconnect linkage and remove handle. Install new handle and secure to metal panel with new pop rivets or sheet metal screws. It may be easier to reconnect linkages by removing the metal panel also.

Apr 11, 2009 | 1998 Chevrolet K1500

1 Answer

Both front doors on my "93" Corsica won't open.


You have to open the Window all the way And I Assume your looking Down Threw the Glass opening to View the Linkage,

their is a Spring for the Return of the latch, While looking at the Latching system, Look for the Spring that When you "Try" to open the Door it's Suppose to Compress, Most likely the Spring is Not Fully Releasing,

You may try WD40, And work the handles for a few mins and Then Try to Unlock the door for it to open, OR you can Try a LONG Screw drive to Slide the Spring to fully Non compressed state and then Make sure the Door Lock is in the Open State before you try the handles..

Feb 03, 2009 | 1995 Chevrolet Corsica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...