Question about 2002 Chrysler Town & Country

Open Question

How do I change the starter? Do I need any special tools?

Posted by on

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Starter fluid worked

you need fuel line disconnect tools without tools you will damage fuel line connectors.

Nov 25, 2012 | 2000 Ford Explorer

1 Answer

How do you change a starter on a 1991 accord wagon its on top of the bell housing

You would have to take the air filter box out to reach the starter, some special tools required to reach to the bolts.

Feb 25, 2011 | Honda Accord Cars & Trucks

1 Answer

What do i need to change a front crankshaft seal on a 3.2 L 2000 dodge intrepid? I heard you need a special tool that i dont have.

Hi, you will need a vibration damper puller and a seal remover. You can rent these or possibly borrow them from Autozone. The seal can usually actually be removed with a screwdriver. If you have an automatic transmission, you will also need a way to lock the engine while removing the big bolt holding the vibration damper/crank pulley on. You can always do this by removing the starter and locking the flexplate with vicegrips or screwdrivers, but some procedures call for a special tool. Please let me know if you have more questions, and thanks for using FixYa.

Feb 12, 2011 | Dodge Intrepid Cars & Trucks

1 Answer

Do I need any special tools to remove and replace an ignition lock set on a 1989 Ford Econoline E-250 Super Duty van? Is there and instructional video on line anywhere? Apparently it is worn and causing...

Well that problem could also be the starter itself sticking.

But no No special tools are required to change out the lock set, you just need to take off the plastic around the steering column and remove the lock cylinder.

You might need wire strippers and crimpers though

Apr 08, 2010 | Ford E-250 Cars & Trucks

1 Answer

91 chev corsica location of starter, any special tools needed

Nothing special about the tools but you will need to make sure you add the shim correctly

Feb 02, 2010 | 1991 Chevrolet Corsica

2 Answers

Can you tell me how to change the starter in an f150 1997 4 wheel drive truck I've cleaned the battery terminals and the starter wire ends from bottom of truck to the the starter. I have a new battery. I...

no special tools needed use a 1/2 inch or a 9/16 wrench for bolts but rule # 1 before you work on any electrical parts on your truck is to disconnect the negative terminal on the battery then take the starter off you 2 blots holding the starter to the engine take them off they maybe a little tight you my have use a little muscle once you take them out pull out the starter then you have to unscrew the cables use the same procedure to install I hope this information is of use GOOD LUCK

Jul 27, 2009 | 1985 Ford F150

1 Answer

Starter for 94 Cadillac El Dorado, I think.

I don't think you need a battery. Check the battery terminals for corrosion and make sure that they are snug. The clicking sound you hear is the lack of voltage going to the starter solenoid. This could be attributed to a poor connection of a wire, or a starter relay in the fuse panel. There are no special tools required to remove the starter but you can have it bench tested at any Advanced Auto Parts free of charge. Good luck

Apr 27, 2009 | 1994 Cadillac Eldorado

1 Answer

Tool needed to install starter?

there is no special tools and it not as bad as it looks

Nov 20, 2008 | 2002 Jaguar X-Type

1 Answer

Starter Motor

yes very easy.... no special tool needed.

Jun 18, 2008 | 1995 Land Rover Range Rover

Not finding what you are looking for?
2002 Chrysler Town & Country Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides