Question about 2000 Hyundai Elantra

1 Answer

Unable to remove gearbox - 2000 Hyundai Elantra

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 366 Answers

Is it that everything is unbolted and off and tranny doesnt slide out,if so,do like i did with mine,i had to pry it out,because release bearing wont detach from throw out bearing,in the process youll damage the spline on the pressure plate,wich means new clutch!

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove 1400 Nissan gearbox out


1 Remove battery earth cable.
2 Remove gear shift lever - usually just pulls out.
3 Remove starter motor.
4 Remove bolts holding prop shaft to gearbox final drive, and remove the prop shaft.
5 Remove all bolts around bell housing holding bell housing to engine.
6 Slide gearbox back to slide spigot shaft from clutch plate.
7 Slide gearbox from under vehicle.
Gearbox is now removed out.

Jan 02, 2015 | Nissan Cars & Trucks

1 Answer

Steps to removing a transmission from a GMC ENVOY 2004 V6, 4WD.


Park the vehicle in a clean dry well lit place. Work with safety in mind. Its always good to take pictures as you strip the/ a assembly. Refer back to pictures if you get stuck. Dis-connect the battery. Remove the gear linkages and speedo-drive and power cables from the gearbox. Remove the starter motor. Loosen the propshaft. Mark the yokes of the propshaft- for upon installation to avoid an unbalanced propshaft. Loosen the centre bearing. Remove the propshaft. Remove the cross member underneath the gearbox if there is one. Loosen bolts around the gearbox to cylinder block. Use a gearbox jack to support the gearbox. Take the bolts out from the gearbox to cylinder block. Pull gearbox backwards. Lower the gearbox. This is pretty much the standard way of removing gearbox. Note, there might be a transfer box, normally with 2 propshafts. Mark the yokes. Remove propshafts, transfer box and then gearbox. Remember to always work safe.

Dec 19, 2014 | Cars & Trucks

1 Answer

Fiat punto8valve 1999. fitted clutch. unable to select 5th and reverse, after adjusting cable . removed and refitted selector bracket with gerbox at the beginning?


when you where taking off the selectors did you remove one of them by taking off a 13nut? if so the selector under this nut dropped into the gearbox and its not lined up properly u need to remove the top of the gearbox and allign it.takes some messing around to get it right

Sep 18, 2009 | 2006 Fiat X1/9

1 Answer

How to remove the gearbox from a 1999 suzuki swift car


disconnect battery remove it & its cradle
jack it up & drain gearbox oil
remove the wheel & undo the axle nut in the centre!
[do not remove it yet]
undo the bottom control arm at its pivot point under the axle then seperate them !
pull swiftly outward to remove the drive shaft from the gearbox!
now there is the gear selector & speedo & clutchcables & starter motor to diconnect & or remove
remove gearbox mount But support the motor from underneath
undo all the bolts around the gearboxes bellhousing!
use a pry or large flat bladed screwdriver to part the gearbox from the engine & lift gearbox up & out! its very tight squeeze in there!!
Im sure now that you regret asking lol
dont forget while its out you may aswell do the clutch
good luck!
Cheers Rob.

Jul 20, 2009 | Suzuki Swift Cars & Trucks

2 Answers

1998 Disco-Unable to remove key from ignition.


If disco is automatic move the transfer lever from high to low box and back again firmly then the key will come out there is a safety feature on the autos to prevent the key being removed if the transfer box is not in either high or low correctly with most dicso;s the transfer shift lever is stiff. through lack of use .once it is pushed in properly the key will release it works every time and I have had four v8 autos
basically you cant remove the key because even though the gearbox is in park if the transfer gears are not fully home the park sensor on the gearbox thinks it is out of gear eg not in park so wont let you remove the key and leave the car out of gear in case it rolls away .Dan

Jun 30, 2009 | 1998 Land Rover Discovery

1 Answer

156 2.0l x reg. unable to select 4th gear, lever will not move into gear. engine running, stopped, just baulks when trying to select.


syncronizer for 4 gear total damaged it happens you need to open gearbox and change the syncro bearing for 4 th not very expensive dont change the gearbox

Jun 11, 2009 | 2000 Alfa Romeo 156

1 Answer

Changing driveshaft on a ford festiva.


you have to pry the drive shaft out it has a clip on the shaft hope this helps

Mar 21, 2009 | 1993 Ford Festiva

2 Answers

Porsche 911 1995 C2 Gearbox Issue


are you using the correct oil for the year of the car,it sounds like it to thick grade of oil

Dec 29, 2008 | 2004 Porsche 911

1 Answer

BEARINGS WORN IN GEARBOX


disconnect lower arms, and remove driveshafts..disconnect all wiring and remove bolts from gearbox bellhousing and remove gearbox from underneath the car

Dec 24, 2008 | 2006 Peugeot 504

2 Answers

Whats the best way to drop the gearbox & transfer case?


remove the carpet on the floor, remove the gear shift lever as well as the 4wd shift lever, remove the drive shaft (both) remove the bell housing bolts, remove the starter, place a hydraulic lift jack below the gear box , then remove the wiring connectors , then remove the cross member , then pull the gearbox out from its positin, drop the gearbox very carefully, when gearbox is on the floor, make sure its sittin on a up right position so it dose not spoil any of the elctric connectors especially the reverse light switch...(that seems to be the easiest way to remove a manual land cruiser gearbox) hope that wil help....

Oct 25, 2008 | 2001 Toyota Land Cruiser

Not finding what you are looking for?
2000 Hyundai Elantra Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...