Question about Volkswagen Golf

1 Answer

N REG POLO changed pads replaced rear wheel cylinder for brake shoes then bled brakes then turn engine on moved car 10ft pressed brake pedal it was like a sponge

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 79 Answers

You must still have air in one of the pipes - not necessaryily only to the wheel you have been working on (though normally that is so). Did youu make sure that the fluid level remained above minimum in the brake fluid master cylinder while you were bleeding the brakes? Possibly a slurp of air went in there and now the other pipes will need bleeding too. Don't panic - just bleed all the brake pipes, making sure that the master cylinder level stays high.

Posted on Sep 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 23 t bucket and i cant get a brake pedal.when i bought it had very little brake so i replaced rear shoes and cylinders,front pads and calipers,all new lines and the master cylinder


Once you have bled the air from the brake lines,clamp off the front brake hoses carefully.Does the pedal feel better now?
Then the pad /caliper fit is allowing too much play.Is the pedal the same?Then clamp the rear hose and try the pedal.Is it fine with the rear hose clamped?If so we now know the problem is at the rear brakes.One common low pedal rear brake cause is brake shoes that do not fit the drums.Remove the drums and look at the shoes,are they showing contact wear fully or just in the middle of the shoe?Remove a shoe and place it in the drum.Can you rock the shoe against the drum surface?Once drums have been resurfaced,the shoes will not fit fully against the drum allowing the shoe the flex when applying pressure to it and this can easily create a low soft brake pedal. Of course rear brake adjustment must be correct once brake shoe contact is correct.To correct brake shoe contact,have your shoes re arc-ed to fit resurfaced drums or install new drums.Don't overlook brake master cyl /brake pedal push rod adjustment too.

Jun 24, 2017 | Cars & Trucks

1 Answer

Brake pedal goes to floor


for the pedal to go to the floor there is still air in the brake system. Start again starting from the longest line bleeding each in turn to the shortest line . make sure you have adjusted up the rear brakes before bleeding as every time you press on the pedal the shoes expand right out and when you take your foot off the pedal the shoes go all the way back in. adjust them manually and do not rely on the self adjuster as it only adjusts on wheel movement

Jul 15, 2013 | 2002 Ford Explorer Sport Trac

1 Answer

Brake problem


Sounds like your braking system is working perfectly as vacuum adided system should. A hard pedal is normal when engine is off then the nvac sftens the pedal. If pedal is moving down too much check your brake pads and/or shoes for wear and adjustment.

Aug 13, 2012 | 1980 Chevrolet Corvette

4 Answers

Brake pedal goes nearly to floor front pads, calipers, brake hoses changed, rotors turned Master cylinder changed, brake booster check valve changed rear brakes checked, drums good no ridge, shoe's...


I would go with not bled correctly

The booster should hold up with a hard pedal until
you start the engine, then vacuum causes it to move
down when pressing on the brake

Sep 16, 2011 | Saturn SC Cars & Trucks

1 Answer

I replaced disc brake pads, rear shoes. wheel cylinder,master cylinder, power brake booster all new. Question: My brake pedal is not solid,goes low to the floor almost. I have bled the master cylinder 1st,...


Check your lines going to the brakes the rubber hose on the 1993 chevy have a tendancy to crack and brake are you using an excess of brake fluid

Sep 12, 2011 | 1993 Chevrolet C1500

2 Answers

Spongy brake pedal even after ABS bleed and base brake bleed.


Did you adjust the rear shoes out? If the rear drum brakes are out of adjustment they will give you a lot of pedal travel. If the pads are worn have no fear of that U-CLIP brake spring, just change one shoe at a time. Take the spring off one side, change the shoe, put the spring back on the post and do the same to the other shoe, no problem.

Dec 03, 2009 | 2001 Chevrolet Venture

1 Answer

1998 Suburan brake pedal gushes air along the firewall.


you got it, the booster is leaking reducing the vacuum to the intake, replace it

Oct 26, 2009 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

89 c1500, full pedal on brakes until started then goes to floor. Bled system,replaced master cylinder and anti-lock system,now has better pedal but code 4 on brake lite that won't go out. Have replaced...


adjust your rear shoes up so that the rear drums just turn, with them ajusted to a low setting the brake pedal will be low .
also when you start your engine it is noral for the pedal to drop because of the boster ! [ but not to the floor ]
Bruce Pike

Oct 10, 2009 | 1989 Chevrolet C1500

1 Answer

Brakes don't work on polo n reg bled them seemed fine till turned engine on moved car 10ft no brakes


did you change the pads? if so when you bled the brakes did you make sure that all air was out of every line? if you bled the brakes for another reason you need to specify why

Sep 25, 2009 | Volkswagen Golf Cars & Trucks

1 Answer

Fiat Uno Pacer - Brake Booster not assist braking


it could be that the master cylinder is bad or the brake booster is bad also check the vacum hose going to the brake booster if it has a hole in it it will lose pressure and make the engine lose rpms

Aug 16, 2009 | 2006 Fiat 124

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...