Question about 1995 Chevrolet Blazer

Open Question

I need to replace the right front turn signal on the side of the headlight. How do I get to it?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 196 Answers

SOURCE: electrical problem

Find the ground wire on one of the lights and add another ground wire to a good clean metal surface and see if that fixes the problem. It defently sounds like a ground problem at one of the lights.

Posted on Jan 07, 2009

Ad

SOURCE: 93 S10 left turn signals not working

Have you tried replacing the flasher? You'd think neither side would blink if the flasher was bad but I've seen this happen and it turned out to be the flasher. You could swap the signal flasher with the 4 way flasher to verify that's the problem before going out and buying one. Should be a few bucks at the parts store.

Posted on Apr 16, 2009

juststinks
  • 98 Answers

SOURCE: how to replace front turn signal bulb

its easy. when the sinal flashes fast its just telling you a light is out. there might be 2 ways to fix this. open the truck look for the housing for the lights. now you may have to just turn the harnest where the wires are. or you just nee a phillps screw driver and unscrew the plastic cover off.

Posted on May 14, 2009

  • 14036 Answers

SOURCE: need replace turn signal bulb

YOU HAVE TO THE FRONT HEADLIGHT HOUSING TO REPLACE THE TURN SIGNAL BULB.

Posted on Aug 24, 2009

Testimonial: "thanks"

  • 231 Answers

SOURCE: Headlight / turn signal switch on 1998 chevy

I suspect you need to replace the lever unit.

Posted on Feb 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change the side light on an aidi a4 1999


Sidelight may mean the turn signal on the side of the car (sidemarker) or the turn signal right next to the headlights.

To replace sidemarker, you need slide it toward the front of the car. You may need to use a little bit of force. Then, pry the bulb out of the fencer hole with your fingers.

For turn signal light next to the headlights, see if you can figure out how to do it from the You tube video:
how to change the side light of audi a4 1996 Bing Videos

Feb 13, 2015 | 1996 Audi A4

1 Answer

Right front side turn signal does not work replaced all bulbs and checked fuses headlight flashers work when hazards are on front to back except driverside turn signal ,in dash right stays solid left


I don't believe it would be a bad ground for just one light. It could be a wire, a socket connector, or the bulb socket itself. See if the wire has power at the socket when signaling left, with key on. If there is power, probably a bad socket or connector. If no power, check for power coming from flasher-the wire going to front left, or driver's side. If you have power from the flasher, but nothing at the socket, the wire has probably broken.
Good luck.

Feb 06, 2013 | Cars & Trucks

1 Answer

Left turn signal pops fuse on infiniti


Check front and rear lights to see if the wiring is arcing to the turn signal on the left side of the car. This is the best guess as it's simply a wiring problem and nothing else, as there is too much current being forced through the turn signal when the headlights are on. Headlights draw much higher current than the intermittant turn signals and therefore pops the fuse.

Mar 02, 2012 | 2011 Hyundai i30

1 Answer

2008 Chevy Cobalt front right turn signal is not working. Back right signal blinks fast. Left signals work just fine. I tried replacing the bulb and it did not work. Do I need to replace the...


No - headlight ok.
The reason that the Right turn signal blinks fast is that there is half the normal load (resistance)
on the right side, since the Right front turn signal isn't working.
Since you replaced the Right front turn signal bulb, your problem lies in the bulb socket or
the wiring to the socket.
(1) try cleaning out the socket - there's probably a contact problem in the socket. You
may need to squeeze the contacts together to provide good contact to the socket contact.
(2) if contacts inside the socket are ok, try back-probing the socket - to make sure that the
socket is getting 12V DC to light the bulb. Replacing a bulb socket is easy, and commonly done.
Any auto parts dtore should be able to sell you a new socket - its just a matter of cutting out the
old one, and then splicing in the new one. Most shops will use small wire nuts, buried under several
wraps of E-tape (electrical tape).
(3) if bulb AND socket ok, you have the worst problem known to man - a wiring fault. In this case,
you'll want to run a new wire from the flasher module (under the dashboard) to the turn signal.

Jul 29, 2011 | 2008 Chevrolet Cobalt

1 Answer

How do I access the front drive side turn signal to replace the bulb on a 2003 Discovery?


You need to access phillips screw next to top right side of driv headlight and slide turn signal assembly forward. It helps if you remove black plastic access plate above headlamp.

Feb 28, 2011 | 2003 Land Rover Discovery

2 Answers

How do you replace the front turn signal on a 2005 Buick Terraza?


Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

Sep 07, 2010 | 2005 Buick Terraza

1 Answer

Left turn signal + headlights


Try turning the 4-way flashers on with the headlights and see if it looks normal or if it looks like they are flashing alternately instead of together. If it looks like they are flashing alternately, you have a bad ground on that bulb. Difficult to explain easily, but bulb grounds through the circuit that is turned off until both circuits are energized, then problems occur. If not, try unplugging the U-Haul harness, they usually are just plug in deals and see if that fixes it.

Nov 25, 2009 | 1998 Nissan Altima

2 Answers

Need replace turn signal bulb


YOU HAVE TO THE FRONT HEADLIGHT HOUSING TO REPLACE THE TURN SIGNAL BULB.

Aug 24, 2009 | 1996 Chevrolet Cavalier

1 Answer

Driver side signals only work when headlights are OFF


What may have happened is either the headlights wiring or the parking lights wiring somewhere along the wiring fused to the left turn signals wiring. Depending on if the turn signals go on when you put the parking lights on or the headlights on.

If the signals come on when you turn on the headlights than you only need to locate the light green wire that comes off the left turn signal harness.

Next follow that wire the entire way back to the firewall looking for another wire fused to that wire as you go.

If there are no signs of this you need to continue looking on the other side of the firewall all the way back to the turn signal and hazard flasher unit which is a black box that connects to a black harness located next to a grey harness behind the knee bolster.

But if the signals come on when you turn on the parking lights than you will also need to check the wiring from the rear left signal and follow that light green wire all the way back to the turn signal and hazard flasher unit.

This should fix your problem, but if not than your problem may lay within the the wiring between the turn signal/hazard switches and the turn signal and hazard flasher unit.

Also you may have a burnt circuit in the junction block. This block is where the light green from the rear left signal and front left signal meet. Don't have a description but if you cannot find it let me know and I will go out to the yard and look myself and let you know.

Apr 22, 2009 | 2004 Dodge Intrepid

1 Answer

Replace broken driver side turn signal lights - left fender


reach screwdriver down between headlight and marker to releace clip, pull forward.

Nov 06, 2008 | 1998 Volvo S70

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...