Question about 2007 GMC Acadia SLE

2 Answers

How to change the low beam lightbulb. I figured out where it is... but need to remove the whole fixture.. how do it do it?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It's so easy to replace the lights in your pacifica that even a girl like me can do it in under five minutes...


Above each light fixture are two screws, most likely they will take a flat-head or common screwdriver. Remove both of them.
The light fixture is ready to come out now. Take your screwdriver and under the front of the fixture gently pry upward and the whole assembly will pop right out. turn it over and remove the correct rubber cap for the bulb you need to replace (outside is low beam, inside is high beam. At least on my 05 anyway) Reach into the back of the fixture and turn the light and socket counter clockwise.
Unplug the old bulb and put in the new! Now just reverse the process.. Note: When putting the fixture back in place, make sure that the lip on the plastic bracket of the fixture goes over the metal frame that you removed the screws from!
Once the screws are in place, if you have not already, snap the bottom of the fixture into place and you are good to go.


Once I knew how to do it, I was able to do it in under 5 minutes and didn't even mess up my nails! lol


Good luck!

Posted on Mar 05, 2013

Ad

Look it over, get involved and remove whatever screws hold it to the body/fender etc. Most screws are Torx type fastners. No torx sockets or driver bits, your done before you start. Torx have been on veh for 25 years.

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to change lightbulb can't get headlight off, have taken out 3 screws and pin


think all you need to do is turn the bulb counter clockwise and pull it out

Aug 29, 2015 | 2006 Buick Lucerne

1 Answer

2003 Pontiac Grand Am brights work but ONE low beam is out ...


You most likely need a new low beam headlight BULB.It has the low and high beam in it and the separate high beam has only high.
You SHOULD have 2 tabs ,one at each end to pull up and the headlight assembly should then come out easily.
Tapping a blown out headlight can reattach the filament for a short time but after that replacement is necessary.

Mar 12, 2017 | 2003 Pontiac Grand Am

1 Answer

Having trouble with a 2010 tiguan . low beam right waring came on as well as rear left signal. I changed the front low beam warning still there and light doesn't wok. What is my next step?


Check grounding on the fixture. Usually the fixture only gets the 12v+ from switch. The 12v- comes from the fixtures mounting or it has a black wire that comes off of fixture and goes to ground.

Dec 28, 2012 | 2010 Volkswagen Tiguan

1 Answer

Need to replace low beam light in my 2002 GMC Safari Van how do I do it?


Open the hood & near the top of the headlight you will see 2 bolts (10mm), remove them. You will notice the whole headlight assembly is loose from the top. Look down into the headlight assembly to the left & you will see another 10mm bolt that connects the outside light fixture. Remove the bolt & that light fixture will fall out (top first). Behind that light fixture you will see your last bolt when you look at the front of the vehicle. Remove it & now the entire light assembly will slide out & give you access to the both high beam & low beam bulbs. Hope this helps.

Read more: http://wiki.answers.com/Q/How_do_you_replace_the_headlight_bulb_located_on_a_1998_GMC_Safari#ixzz25o5cWhZA

Sep 07, 2012 | Cars & Trucks

1 Answer

Both high beams do not work, but low beams do.


Need new lightbulbs. Lowbeam will still work evan after highbeam elament is burnedout in bulb. If separate bulbs are used for high and low beam,then change high beam bulbs only. If does not fix then check fuse or wires and make sure plug to bulb is in correct position. But probably just need new bulbs.

Oct 22, 2011 | 2005 Honda Pilot

1 Answer

My right headlight (low beam) is out. How do I change the bulb?


Open hood, on left side of vehicle behind the light fixture look for white nylon clips that just lift
Pull up about 1.5" and they come free from the fixture. At this point the entire light assembly can be moved forward. Disconnect the wiring harness and the whole fixture comes out allowing you access to all the bulbs.
Reverse process to reassemble

Jan 21, 2011 | 2002 Buick LeSabre

1 Answer

How do change low beam lightbulb on a 2007 dodge ram 1500


Removal & Installation-Get at it from behind the lens assembly.
These instructions show how to remove and replace the whole light assembly but shows a diagram
on what it looks like.

To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following: dod_ram15_02-04_headlmp.gif

    • Negative battery cable
    • Push pins
    • Bolts connecting headlamp unit to fender
    • Bulb sockets from headlamp unit
    • Headlamp unit
To Install:
  1. Install or connect the following:
    • Bulb sockets
    • Headlamp unit to fender with the bolts
    • Seal and push pins
    • Negative battery cable
prev.gif next.gif

Jan 14, 2011 | 2007 Dodge Ram 1500 Quad Cab Sport

1 Answer

2004 IS 300 - does it have HID or Halogen low beam lightbulbs?


Your low beam is a HID bulb, number D2R, and your high beam is a halogen 9005 bulb

Jul 27, 2009 | 2002 Lexus IS 300

2 Answers

2003 volvo s60, how do i adjust headlights


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 18, 2009 | 2004 Volvo S60

Not finding what you are looking for?
2007 GMC Acadia SLE Logo

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...