Question about 2000 Dodge Dakota Quad Cab

Open Question

My plastic clip on drivers side front window regulator broke. How do I remove damaged one & install new regulator

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace the window regulator on the drivers side


Please don't forget to rate! Thanks!!!

Motor & Regulator
  1. Remove the front or rear carrier assembly.
  2. Slide a hammer handle between the window guide and carrier assembly until the hammer handle end presses on the gears of the carrier assembly.
  3. Unfasten the bolts (1) and remove window regulator.

c17hydro_62.gif

Unfasten the bolts (1) and remove window regulator


To install:


NOTE:By removing window regulator motor, gearing shifts, it is not centered



c17hydro_63.gif


  1. When installing window regulator motor, the gears must be aligned until the window regulator motor is centered again.
  2. Attach and tighten the bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.
  3. Carrier assembly with window regulator, installing:
    • For replacement part carrier assemblies, the gearing is secured in place with a cable tie.

c17hydro_64.gif

For replacement part carrier assemblies, the gearing is secured in place with a cable tie (1)


  • Slide a hammer handle between window guide and SF so far until hammer handle end presses on gears of SF.
  • Remove the cable tie .
  • By removing window regulator motor, gearing shifts, it is not centered.
  • When installing window regulator motor, gears must be aligned until window regulator motor is centered again.
  • Attach and tighten bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.
  • // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 23; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

    Dec 09, 2010 | 2001 Volkswagen Cabrio

    2 Answers

    The passenger side window, something broke down in the door, the motor for the power windows still works, but there is nothing holding the window up? What broke? Is it a do it yourself job to fix it?


    Its the window regulator thats broke. Most are made with plastic brackets and cable. The plastic breaks and the cable goes nuts then nothing is holding the window. You need to get a regulator, if you can take the door panel off you should be able to handle installing the window regulator.

    Dec 08, 2010 | 2002 Buick Rendezvous

    1 Answer

    Remove and replace drivers door 1999 taurus?


    Please don't forget to rate! Thank you!

    Removal & Installation
    c17hydro_32.gif

    The door-to-body mounting



    c17hydro_33.gif

    Detach the door wiring from the connector


    This is a two person operation.

    1. Remove the two door check-to-body retaining screws.

    WARNING

    Cover the end of the check strap to prevent possible paint damage.


    1. On the rear doors, remove the rear door trim panel, detach the electrical connectors from the components (if equipped) and remove the wiring harness from rear door.
    2. On the driver's side front door, disconnect the window regulator wiring, if so equipped, by removing the wire connector cover, loosening the screw and separating the connector halves.
    3. On the passenger side front door, remove the rubber harness protector from the body to reveal the electrical connectors. Detach the two electrical connectors.
    4. If the door is to be replaced, transfer the following components to the new door if in usable condition:
      • Door trim panel
      • Watershield
      • Outside mouldings
      • Trim clips
      • Window regulator
      • Door latch components.
    5. Remove the hinge retaining screws and nuts from the door and remove the door.

    To install:

    1. Position the door onto the hinges and hand tighten the screws.
    2. Align the door and tighten the screws to 19-25 ft. lbs. (25-35 Nm).
    3. If removed, install the wiring harness to the rear doors.
    4. Attach the electrical connectors to the door panel.
    5. Install the door panel(s).
    // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 31; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

    Nov 20, 2010 | 1999 Ford Taurus

    1 Answer

    How to remove front dopr panel on 1995 Lincoln Town Car


    Front Door Panel - Town Car - Removal
    CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove.

    Snap out two door pull strap retaining screw covers. Remove screws.

    Remove two screws on front and rear side of front door trim panel.
    The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.

    NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors.

    Disconnect driver seat regulator control processor switch (driver door only) if equipped.
    Twist out interior lamp wire assembly and remove the front door trim panel.
    Installation

    Ensure plastic watershield is secured to door panel.
    Position front door trim panel to door. Connect interior lamp wiring.
    Position the window regulator control switch housing and connect switch connectors. Install the retaining screws.
    Connect driver seat regulator control processor (14C708) (driver door only) if equipped.
    Align door lock side to its mating slide on the sheet metal (front doors only).
    Snap in front door trim panel. Ensure all retainers fit properly.
    Install two retaining screws on front and rear side of front door trim panel .
    Install two retaining screws and pull strap covers.

    Good luck Remember rated this).

    May 31, 2010 | Lincoln Town Car Cars & Trucks

    1 Answer

    Need to find a way to take off the drivers side window motor


    Motor
    1. Disconnect the negative battery cable.
    2. Remove the door trim panel and watershield.
    3. Detach the motor wires at the multiple connector.
    4. Remove the motor retaining screws using Torx® drive bit set D79P–2100–T or equivalent, and separate the motor from the bracket and cable drum housing.
    5. Remove the motor from inside the door.
    To install:
    1. Position the motor and drive to the cable drum housing and motor mounting bracket. Install the 3 motor screws and tighten.
    2. Connect the power window motor wiring.
    3. Connect the negative battery cable.
    4. Check window operation.
    5. Install the watershield and door trim panel.

    Door Panel
    1. Disconnect the negative battery cable.
    2. Snap out the two door pull strap retaining screw covers. Remove the screws.

    CAUTION To avoid breakage of the door pull covers, insert a small screwdriver diagonally between the pull strap and chrome bracket. Snap out both sides then remove.


    1. Remove the two screws on the front and rear side of the front door trim panel.
    2. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.

    NOTE Do not use the front door trim panel to remove the trim clips from the door inner panel. Replace any bent, damaged or missing push pins.


    1. Remove the window regulator switch housing from the back of the front door trim panel. Lift up the housing and disconnect all connectors from the switch housing.
    2. Disconnect the driver seat regulator control processor switch if equipped.
    3. Twist out the interior lamp wire assembly.
    To install:
    1. Ensure that the plastic watershield is secured to the door .
    2. Position the front door trim panel to the door. Connect the interior lamp wiring.
    3. Align door lock side to its mating slide on the sheet metal.
    4. Snap in the front door trim panel. Ensure all retainers fit properly. Install the two retaining screws on the front and rear side of the front door trim panel.
    5. Connect the driver seat regulator control processor, if equipped.
    6. Position the window regulator control switch housing and connect the switch connectors. Install it to the front door trim panel by snapping it in, or by installing the screw at the rear.
    7. Install the two retaining screws and pull strap covers.
    8. Connect the negative battery cable.
    053777a.gif

    Aug 27, 2009 | 2000 Lincoln Town Car

    1 Answer

    How do I install a new windows motor- to include the cable drum (drivers side). The old motor burned up and the cable broke. Thanks Hans


    You'll need to buy a new motor and regulator. You can go used or new, it's up to you. The regulator will include the cable.

    - Remove the interior door trim,
    - Disconnect the power cable from the window motor,
    - Remove the window bump-stops (one at the front, one back),
    - Remove the glass window from the regulator (two bolts),
    - Slide the glass window out of the top of the door,
    - Remove 3 nuts from the window motor,
    - Remove all window regulator bolts,
    - Slide the motor & regulator assembly out the top of the door.

    - Mount your new motor to your new regulator,
    - Install the new motor & regulator assembly in the reverse order.

    Jul 27, 2009 | 2003 Hyundai Tiburon

    1 Answer

    Drivers Side Electric window 1993 SC400


    The motor/regulator comes as an assembly with the wire and clips. You don't need to remove the window, just unbolt it from the regulator, and hold the window up till the new regulator is in, then remount it.

    Jun 10, 2009 | 1995 Lexus Sc 400

    1 Answer

    Fallen driver's side window


    probably need a new window regulator. ebay. 93 to 98 should fit.

    Section 01-05: Trim, Interior 1998 Villager Workshop Manual
    REMOVAL AND INSTALLATION Trim Panel(s), Door Front
    Removal
    1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
    1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
      Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




    1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
    1. Pull the shop rag back and forth to release the window regulator handle clip.




    1. Remove the three cover caps and front door trim panel screws.
    1. Remove the one front door trim panel capped screws from the door pull handle.
    1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
    1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
    1. Remove the front door trim panel.
    Installation
    To install, reverse the removal procedure.
    ---------------------------------------------------------
    Window Regulator, Power Front Door
    Removal
    1. Disconnect the battery ground cable (14301) .
    1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
    1. Remove the two front door brace bolts and the front door brace.


      415712f.gif

    1. Disconnect the front window regulator electric drive electrical connector.
    1. Remove the four front door window glass regulator track bolts.

      67b6136.gif


    1. Remove the three front window regulator electric drive bolts.
    1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
    Installation
    1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
    1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
    1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

    Apr 29, 2009 | 1998 Mercury Villager

    1 Answer

    Front right door window will not go up or down, it is electric. it works, some times, and some times not. it is in the down position. Would like to move to up position. I live in Arizona, I need it up for...


    does it act the same whether you use the driver door switch or the passenger door switch? Please rate as fixya if this helps. thanks

    here's repair procedure

    Window Regulator, Front Door, Explorer Removal
    srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
    1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
    Trim Panel, Front Door, Explorer Hi-Series, Two-Door and Four-Door Removal and Installation
    1. Remove the two screws retaining the front door trim panel (23942) located above the window regulator handle (23342) . Also remove one screw in the upper front portion of front door trim panel .
    1. Remove inside door handle cup (22634) at the window regulator handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
    1. To remove window regulator control switch (14529) and outside rear view mirror control (17B676) , use notch located at lower end of outside rear view mirror control using a screwdriver to lift and remove.
    1. Remove outside rear view mirror control from front door trim panel pulling wire harness from inside of front door trim panel .
    1. From bottom of outside rear view mirror control, remove two screws and disconnect connector from switches. NOTE: Do not pull on the front door trim panel to remove clips from the inner panel holes.
    1. At each plastic clip location, pry the front door trim panel away from the door inner panel using the front door trim panel removing tool from Rotunda Moulding Trim Kit 107-00401 or equivalent. NOTE: Pay special attention to the cut-out in the door trim panel for the door handle, so that it clears the handle during removal without breakage.
    1. When wiring and disengagement of trim clips is completed, it is recommended that to remove panel, lift slightly to remove flange at the top of door trim panel from trough in the glass weatherstrip.
    1. Disconnect socket and bulb from illuminated interior lamp (13776) before total removal of front door trim panel. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the front door trim panel to the front door trim panel , firmly loading clips into slots provided on front door trim panel .

      Trim Panel, Front Door, Explorer Hi-Series Four-Door

      a9ce4e4.gif
    1. Remove inside door belt weatherstrip and glass stabilizer.
    1. Remove front door window glass as described in this section.
    1. Remove two nut and washer assemblies attaching the equalizer bracket.
    1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
    1. Remove window regulator electric drive and front door window channel bracket from vehicle.
    1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
    1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

      9b5ccd1.gif

    Installation
    NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
    1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
    1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
    1. Install equalizer bracket.
    1. Install inside door belt weatherstrip and glass stabilizer.
    1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
    1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
    1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

    Apr 20, 2009 | 1994 Ford Explorer Limited

    2 Answers

    Need help with fixing power window


    I'm pretty sure, that is sold as a regulator unit only. And it's not cheap. Sometimes it's cheaper at a glass place than the dealer.

    Mar 06, 2009 | 2001 Oldsmobile Alero

    Not finding what you are looking for?
    2000 Dodge Dakota Quad Cab Logo

    Related Topics:

    78 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8514 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...