Manual side window for 1989 Chrysler Caravan control for opening and closing has probably become partially disconnected from the handle inside. It no longer directly controls the window. I heard and felt something give way. I use it alot because I enter and leave a parkade that requires me to put a card in a slot to open the entrance and exit. Yesterday I couldn't roll down the window, but while I was driving the window fell down and I could roll it back up. Today I failed to roll it down then while the car was parked it fell down. I haven't suceeded in rolling it back up this time. I think I may be able to fix it if I take the panel off the inside of the door to get at the mechanism?

The rod from the handles to the lock mechanism could have come off or become bent to the point that it won't work the latch anymore. The prior problems were probably just symptoms of the problem you have now. Will have to take the door panel off and manually trip the latch.

inside the mechanical lock (The part that actualy holds the door shut when you close it) there is a switch that informs the control unit that the lock is either locked or unlocked.
These switches fail sometimes, when this happens the control unit is not aware that you have opened the door, and therefor will not wind the window down slightly.
The switch is integral with the lock unit, and they are not easy things to replace either.

probably a solenoid thats not opening or closing. you can get one from a junk yard. its located inside the door. if you cant install it, have a shop you trust do the work.

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull back the weather seal and you'll be able to get to the tracks. You may need to get some replacement clips to remount the window to the track

It sounds like the the linkage, actuator (power locks), or the mechanism has broken or become dislodged.
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull back the weather seal and you should see everything and hopefully see the cause.

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

You need to take inside door panel off This just clips on but there are screws in armrest and inside door handle look for any other small square covers that may hide screws Lift panel up Make sure window is up Disconnect wiring from panel and you can now get at door handle linkage and bolts

The connector should be inside your door panel. On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

1, Disconnect the able from negative terminal of the battery.
2. Pry the courtesy light from the door trim and disconnect the wire connector..
3. Remove all door trim panel retaining screws and door pull armrest assemblies.
4. Remove the door switch panel and the control switch panel and the control switch assembly.
5. On models with memory seats/mirrors, use small-flat bladed pry tool to remove and disconnect the wire.
6. Grasp the trim panel lift up and pull out to detach it from the door. Disconnect the inner door handle lock rod from the handle. Unplug any electrical connectors remaining and remove the door panel.
7. To install, connect the wire harness connectors and place the panel in position in the door. Press the trim panel down into place until the hooks are seated.
8. Install the armrest/door pulls, the courtesy light and the window switch'
9. Reconnect the battery


Also. You will need star pattern drivers to remove the window and motor from your door. If you have all the equipment it should only take you 1 hour.