Question about Ford Excursion

Open Question

Turn signals and overhead mileage computer and compass quit working simultaneously. Brake lights still work and fuse checks OK. 2005 6.0 excursion xlt ?????????????? I'm stumped.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Compass not working on 2006 Mercury Grand Marquis


Electronic Compass The compass display and module are contained in the overhead console and are replaced as an assembly. For additional information, refer to Section 501-12 . The compass display can be turned off and on by pressing the MODE button in the overhead console. The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W, or NW.
Inspection and Verification
NOTE: Press the MODE button to turn on the display.
  1. Verify the customer concern by operating the vehicle along roads of known direction to duplicate the customer concern with the compass.
  1. Visually inspect for obvious signs of mechanical or electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Compass module
  • Central junction box (CJB) fuse 15 (7.5A)
  • Circuitry

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the fault is not visually evident, determine the symptom and GO to Symptom Chart .
Pinpoint Test A: The Compass Is Inaccurate/Inoperative
Normal Operation The compass receives battery voltage from the central junction box (CJB) through circuit 964 (DB/LG). Ground for the compass is supplied through circuit 676 (PK/OG).
    Possible Causes
  • fuse
  • circuit 676 (PK/OG) open
  • circuit 964 (DB/LG) open or short to ground
  • compass zone setting
  • compass calibration
  • compass module
PINPOINT TEST A: THE COMPASS IS INACCURATE/INOPERATIVE NOTE: Always set the zone and calibrate the compass before replacing an inaccurate compass.
NOTE: After installing a new compass, always set the zone and calibrate.
Test Step Result / Action to Take A1 CHECK THE OVERHEAD COMPASS DISPLAY
  • Key in ON position.
  • Check the overhead display.
  • Does the overhead compass display remain on after prove out?
Yes
GO to A3 .

No
GO to A2 . A2 CHECK THE COMPASS MODE
  • Press and release the SELECT switch on the overhead console.
  • Does the overhead compass display turn on?
Yes
If the compass display turns on correctly, GO to A3 . If the compass display turns on, but the heading is inoperative/inaccurate or the display indicates VAR, GO to A4 . If the compass display turns on, but it does not display all directions, or indicates CAL, GO to A5 .

No
GO to A7 . A3 CHECK THE COMPASS DIMMING
  • Turn the headlamp switch to the parking lamps ON position.
  • Does the compass display dim?
Yes
TURN the headlamp switch to the OFF position. GO to A4 .

No
TURN the headlamp switch to the OFF position. GO to A8 . A4 CHECK THE COMPASS ZONE SETTING
  • Set the compass to the correct zone for your location. Refer to Compass Zone Adjustment in this section.
  • Does the zone adjustment set correctly?
Yes
GO to A5 .

No
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation. A5 CALIBRATE THE COMPASS
  • Calibrate the compass. Refer to Compass Calibration in this section.
  • Is the compass calibrated correctly?
Yes
GO to A6 .

No
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation. A6 CHECK THE COMPASS ACCURACY
  • Position the vehicle at each of the 8 directions (N, NE, E, SE, S, SW, W, NW) and verify that the displayed heading is accurate. The vehicle must be stationary for at least 10 seconds at each direction.
  • Is the compass display accurate in each direction?
Yes
The compass is OK. REVIEW the operation of the compass with the customer.

No
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation. A7 CHECK THE VOLTAGE SUPPLY TO THE OVERHEAD CONSOLE
  • Key in OFF position.
  • Disconnect: Overhead Console C930.
  • Key in ON position.
  • Measure the voltage between the overhead console C930-1, circuit 964 (DB/LG), harness side and ground.
  • Is the voltage greater than 10 volts?
Yes
TURN the key to the OFF position. GO to A9 .

No
VERIFY the CJB fuse 15 (7.5A) is OK. If OK, REPAIR the circuit. TEST the system for normal operation. A8 CHECK THE DIMMING CIRCUIT
  • Key in OFF position.
  • Disconnect: Overhead Console C930.
  • Turn the headlamp switch to the parking lamps ON position.
  • Measure the voltage between the overhead console C930-4, circuit 484 (OG/BK), harness side and ground while rotating the instrument panel dimmer switch.
  • Does the voltage vary between 0 and 10 volts?
Yes
GO to A9 .

No
REFER to Section 413-00 for further diagnosis of the instrument cluster and panel illumination. A9 CHECK CIRCUIT 676 (PK/OG) FOR OPEN
  • Measure the resistance between the overhead console C930-2, circuit 676 (PK/OG), harness side and ground.
  • Is the resistance less than 5 ohms?
Yes
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation.

No
REPAIR the circuit. TEST the system for normal operation.

Nov 30, 2017 | Mercury Grand Marquis Cars & Trucks

2 Answers

Light has gone out on the console display for compass and temp on the 2006 Toyota Tacoma headliner. Trying to find out which fuse to replace


2005-2009 Toyota Tacoma Overhead Console Fuse test
* does your cruise control work?
* do you brake lights work?
* does your dome light work?
The 10 amp IGI #2 fuse controls several other components including the dome light, cruise control, and
brake lights. If these are working but the compass is dim, intermittent, or dead then the control module
has gone bad.
This is a very common problem with the 05-09 Tacoma. The console is very prone to internal failure. I offer a reasonable repair service with a lifetime guarantee, check it out: www.autoclockrepair.com
There is a bunch of useful info there. Drop me an email if you have questions, thanks!

Nov 19, 2010 | 2005 Toyota Tacoma

2 Answers

Toyota tacoma temp & compass not working


The overhead console is quite prone to internal failure. Dim, intermittent, or dead displays are a common symptom of an internal failure. We offer a reasonable repair service with a lifetime guarantee. Check it out: www.autoclockrepair.com

Jul 20, 2010 | 2005 Toyota Tacoma

3 Answers

The compass and outside temp on my 2006 Toyota Tacoma quit working. Is there a fuse for this unit and where would I find it?


Are your cruise control, dome, and tail lights also out? If so then it is a fuse. If not then the control unit has gone bad internally. You may be able to get it fixed under your warranty.
If it is not covered by your warranty, check out
www.autoclockrepair.com. We offer a very reasonable repair solution.

May 11, 2010 | 2006 Toyota Tacoma

1 Answer

The compass and fuel mileage/dte overhead display has stopped working and gone blank. no lights etc. what do i do to repair it?


The overhead console is quite prone to internal failure. Dim, intermittent, or dead displays are a common symptom of an internal failure. We offer a reasonable repair service with a lifetime guarantee. Check it out: www.autoclockrepair.com

Feb 16, 2010 | 2004 Ford F250

3 Answers

Is there a fuse for the overhead compass/temp dispaly for a 2006 Toyota Tacoma and where is it located?


The 10 amp IGI #2 fuse controls several other components including the dome light, cruise control, and brake lights. If these are working but the compass is dim, intermittent, or dead then the control module has gone bad. You can get a replacement from toyota but I believe it costs $500+.
I offer a repair service with a lifetime warranty. Check it out:
www.autoclockrepair.com
thanks!

Jan 14, 2010 | 2006 Toyota Tacoma

1 Answer

Front driver turn signal quit. changed bulb, worked for short time, then quit. bulb OK. passenger side quit 1-2 months later. bulb OK. neither front emergency flasher work. automatic daytime front lights...


Check for head light (daytime)relay to be bad,this might have to do with the turn signals also,if the turn signals on this car,also have running lights in them,If this relay is not bad,replace the body control module.

Nov 07, 2009 | 2005 Pontiac Grand Prix

1 Answer

For my 2005 ford explorer Sport trac the overhead thermometer and compass stopped working at the same time the lights in the buttons for cruise control on my steering wheel stopped working, but only on the...


Hi,

There is a fuse to power the compass it is the central junction box.it is behind left of dash fuse number 21 takes a 5 amp fuse. If that fuse is ok you need a good scan tool to see what the instrument cluster is saying like codes. Good luck

Dec 19, 2017 | 2005 Ford Explorer

1 Answer

Rear brake lights don't work


you prob got a trailer plug prob bad wires if not tail lights run through turn signal switch tell fix ya bout me ok

May 23, 2009 | 2005 Chevrolet Silverado 2500HD 2WD

1 Answer

No brake lights and no turn signal


Check the fuses that are associated with the brake lights and turn signal. The fuse box is located below the steering column and the fuse box diagram (for fuse assignment) is located in the owner's manual. I hope this helps.

Dec 20, 2008 | 2001 Ford Excursion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...