Question about 1990 Daihatsu Rocky

2 Answers

Cant put hub lock back together need a picture to see.. rocky 1985 model

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

Send me a e-mail, and i will send you the diagrams, I have a 1990 rocky... lioncubb70@yahoo.com

Posted on Feb 07, 2010

Take the other side apart and lay every thing out so you remember going back together

Posted on Sep 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove hub assy. 84 bronco 4x4, manual lock outs


if you are talking about taking the manual lockout hubs off, then first take tire off then if the clips are still on the lugs use a screw driver and pry them up so you can spin them off the lugs, then the hub will come right off. when putting them back on the clips are not really necessary because the wheel will hold it on.. hope that helps..

Oct 26, 2011 | 1985 Ford Bronco

1 Answer

How to remove routers for a for bronco 85 302 full sized


Removing rotors.

1. Jack up, put on jack stands and remove tire (obviously)
2. Remove caliper
3. Remove bolts holding locking hub body to hub
4. Remove snap ring from end of axle, Remove hub retainer ring from ID of wheel hub. Use a small screwdriver or pick to start it out of the groove. Remove the hub body
5. Remove the outer bearing lock nut, lock washer and the inner adjusting nut
You need the special socket for this OTC #7158 or similar
6. Remove the outer bearing and then the hub
7. To separate the rotor from the hub, use a soft faced hammer to drive the studs out
8. Turn the hub over and set the new rotor in place. Put the studs back in.
9. I will usually use an air hammer to drive the studs back in. Alternating in a circular pattern. If you don't have access, you can use a large diameter punch or another hammer on the back of the studs.
10. Now would be a good time to repack the bearings and replace the wheel seals. Pull the spindles and check the bearings and seals in the back of them. If they are not rusted, slab some grease on them and put back together.
11. Install the hub and rotor assy, and the outer bearing and bearing adjustment nut.

Apr 25, 2010 | 1985 Ford Bronco

1 Answer

Need diagram for hub assembley.


is it a stock or an after market hub?? Like Warn?

Sep 11, 2009 | 1985 Chevrolet Chevy

1 Answer

Front hub is lose isit hard to fix?


not that bad just don't over tightin it make it tight and then back it off then put 15 foot pounds on it and put it back together.

Aug 03, 2009 | 1985 Ford F150

1 Answer

The passenger rear hub,,i have removed the 8 bolts and the axle but do not know how to remove the funny looking nut thing to get the hub off


You need to use a socket, but first you have to bend the tabs of the lock collar away from the first nut. There are two of them in there. Don't forget to put the lock collar back in when you put it back together.It's necessary.
You can probably borrow the socket from a truck repair mechanic or machine shop, or you may be able to get it from a place like Autozone. Try to borrow or rent it if you can, it's not cheap.

Jul 12, 2009 | 1985 Chevrolet C2500

1 Answer

We have a daihatsu rocky 4 x 4 independent. having trouble undoing front wheel bearing. help please


ensure trans is in 4h and lockinghub control handle is in FREE position. raise vehicle and remove front wheels. remove caliper and locing hub cover. remove snapring and locking hub. remove outer wheel bearing lock nut,lock plate and adjusting nut. remove bearing and disc. remove oil seal from hub and remove inner bearing.

Jun 24, 2009 | 1990 Daihatsu Rocky

2 Answers

How to assemble left rear bakes on 1985 crown victoria LTD


Go to (autozone.com) and sign up for free access to manuals for all that with pictures, plus parts prices etc.

Jun 02, 2009 | 1985 Ford Crown Victoria

1 Answer

Hub lock


try this website: jcwhitney.com and the phone number is 1-800-865-4227

Nov 12, 2008 | 1990 Daihatsu Rocky

Not finding what you are looking for?
1990 Daihatsu Rocky Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...