Question about 1992 Chevrolet S-10

2 Answers

I have a 92 S10 that does not get fuel. the fuel pump is working the injector relay seems to be working the injector gets power to one line on each injector and i can hear the injectors hum when i turn on the key the computer was damaged by water and I am thinking about changing it

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 242 Answers

That would be the place I would start also, comnputers and water-----O.K. ALL electrical items and water in genreral don't get along well. Even though it appears that you have dried them out, some water will remain- this adds up to corrosion. It sounds as if this vehicle was at least partialy flooded, wich means that everything electical that was under water either needs to be replaced or at least taken apart and cleaned and sealed. The wires of course will also allow water to wick into them.They are just a hollow tube with wire going through them when you get right down to it. If it were mine and it had been under water, even part way on the inside--I'd get rid of it.

Posted on Sep 26, 2009

Testimonial: "Thanks it is running now got a computer for $40 have $100 in it and just gonna drive it till it dies it was a free truck so I guess I can't complain "

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,036 Answers

YOUR PCM CIRCUIT BOARD THAT CONTROL THE INJECTORS IS NOT TRIGGERING THE INJECTORS.I WOULD SCAN IT FIRST BEFORE BUYING A NEW PCM.SCAN IT TO LOOK FOR PCM FAILURE CODE.

Posted on Sep 26, 2009

Testimonial: "Thanks for the help I got a used computer for $40 and the truck is running great now. I got it for free and have $100 and just using it for a beater."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 s10 not getting power to new fuel pump


Check the fuse that provides the power to the fuel pump. Possibility exists that you blow the fuse during the replacement.

Semper Fi,
Z

Jun 07, 2017 | Cars & Trucks

1 Answer

92 volvo 960 no injector pulse how to fix and no power to the fuse block for 30 & 31 fuses for fuel system


check your PGMFI (Fuel Injection Main Relay) if it's good then check the Fuel Pump for power with a probe tester. what do fuses 30 & 31 operate? maybe there is a short and maybe it has to do with those 2 fuse lines working against each other or maybe they are bumping heads with the injectors electrical wiring. my first advice is to check the fuel injection main relay and the fuel pump first.

Jan 08, 2016 | Volvo 960 Cars & Trucks

1 Answer

I have a 92 s10 blazer 4x4 it has a new fuel pump and fuel injectors and filter and oil filter when you push the gas to hard it's not getting gas it also goes dead when driving down the road. It...


First things first, you need to check your fuel pressure AND flow. If you have damaged, or kinked fuel pipes you will have good pressure, but as you load the engine up (put your foot down) your flow is insufficient and you get lean misfire/overheating/cutting out. Bridge the fuel pump relay so you can run the pump without the engine. Get a large jug, suitable for catching fuel, open the fuel supply line and put the pump side in to your jug. Run the pump for 30 seconds, so long as the jug isn't filling up too fast. You should get a minimum of 2 litres of fuel, less and you have a restriction somewhere.

Sep 13, 2013 | Cars & Trucks

1 Answer

1992 4.3 v6 tbi s10 starting problem. Won't squirt


Are the injectors getting power and a ground signal from the computer ?

Sep 06, 2013 | Cars & Trucks

1 Answer

Injector not working why put new injector new computer new fuel pump does it have injector relay 1987 celebrity


Check fuel pressure. Have you replaced the fuel filter on schedule? Verify that the fuel pump is getting power. Power goes through an in-line fuse, then the fuel pump relay or the oil pressure sensor. (The relay bypasses the oil pressure sensor while the engine starts, but fuel pump power goes through the sensor during normal run operation. If you lose oil pressure, the fuel pump is shut off to protect the engine.) On four-cylinder models, the fuse is in the fuse block (E PUMP 10)
The fuel injectors are connected to the ECM fuse on one side and straight to the engine computer on the other side. Check the connectors and wiring, especially at the injector.

Aug 26, 2011 | 1987 Chevrolet Celebrity

4 Answers

Im working on a 95 s10 blazer.It has the 4.3 engine.It will only start if it is sprayed with starting fluid.the fuel pump,fuel filter,and pressure regulator have all been replaced.Seems like the system...


It sounds like the fuel pump is not working. Perhaps the install was not completed correctly. Things to check, fuel pump relay, wiring, voltage to the pump.
The priming happens as soon as you put the key in and turn it to "acc" (you may hear a humming sound). Then once you turn it to "start" the injectors and spark plugs start firing.
Another possibility is that the fuel filter was installed backwards.

Apr 22, 2010 | 1995 Chevrolet S-10 CA Edition

1 Answer

I have a 92 s10 4.3 v6 at first when i stepped on


fuel filter clogged? fuel pump problem? Maybe Injector bad (TBI) or screen stopped up with rust around injector.

Feb 20, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

No power to injectors


are they plugged in?
check the fuse

Dec 13, 2008 | 1992 Chevrolet S-10

1 Answer

Not getting any fuel to the injectors


the fuel pump in the tank will be bad

Aug 27, 2008 | 1992 Volkswagen Jetta

Not finding what you are looking for?
1992 Chevrolet S-10 Logo

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...