Question about 1996 Dodge Dakota

1 Answer

No power in take off from frist gear...Just had trany rebuilt and is still doing the same thing. The o2 sensor has been bad for over 2 years and I never had a problem with the power before. What could be the problem. The gas cables are connected correctly.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Dodge Master
  • 3,433 Answers

First of all, change the o02 sensor so the control mod is not getting mixed signals. How does your cat con check out for free flow?. and last but less likely is the maf sensor. I think its the powertrain controll mododule.. It controls Converter lockup, shift patterns fuel and all sorts of things. Replace the 02 sensor, Disconnect your bat neg for a few minutes and see what happens when you start it up again. Good Luck, Ned

Posted on Sep 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000gmc put a rebuilt trany in now wont shift.


The module for the electronic brake control may have a bad ground with 15 years on it. Did the trans not shift at all after installing it ?

Mar 04, 2015 | 2000 GMC Sierra

2 Answers

My 2004 mercury monteray is experiencing jerking while driving up inclines. I changed the fule filter and it was real dirty when i took it off and replaced with a new one, it went away for about 3 weeks...


Spark Plugs--change every 3 years, not over 70,000 miles
Bad EGR Valve
Ignition Misfires
Worn out O2 Sensors---- change front 2 at 100,000 miles
Clean MAF Sensor-----clean- once or twice a year

Your trans failed, because the fluid has to be
changed every 3 years,30,000 miles ,power
steering also 3 years

Feb 20, 2011 | 2004 Mercury Montery

1 Answer

2003 lincoln navigator idles rough. had cylinder 6 replaced (was bent) had both heads redone, replaced fuel pump. Still idled rough and would stall when stopping or turning. took to other mechanic. They...


I once owned a trans repair shop-
if your trans fluid was in any way other than
pink,your trans may as well come out
and be rebuilt

You have coil misfires as you know,several shown,
most likely only 1 real bad one.

You have O2 sensor codes as well as MAF

The only issue you have is to find the bad
coil
You can't do that buy the codes you have
You have to walk a new coil till you find the
really bad one or get professional help
Don't count on them getting it right

After the misfire and coil issues are solved
there are other thing that can be looked into

I could fix this for you but that's not an internet
option

I definitely would stay away from a dealer.

Why was the trans let go until the fluid was
black?
Not to be hurtful -but it is a well known fact
for decades, that trans fluid and power steering
fluids get changed every 30,000 miles on ALL
vehicles and never past 3 years.

Wish I could have been there sooner, before you
got it or since.

Feb 12, 2011 | 2003 Lincoln Aviator

1 Answer

1.Can a flashing hold light/faulty mass air flow sensor burn the clutches in a transmission? 2.if vehicle reves out after changing into second gear and transmission is rebuilt and problem still persist...


The ecm would not cause this, it sounds like someone did a poor rebuild, if the engining is reving and the car doesnt what to go then the clutches may be bad, a mass are flow would not cause a trany to go bad, the flashing hold light is a problem but should not be happening after the trany was just rebuilt, something is not right here, the trany was just rebuilt and now the hold light flashes and the motor rev going into 2nd gear, that trany has problems a bad ecm wouuldnt cause this slipping reving problem you are having , i would have a trany shop check to see if that trany was really rebuit.

Jan 12, 2011 | 1998 Subaru Forester

1 Answer

My transmission pan has metal shavings and it won't shift out of low gear. is it a sensor or do i need to rebuild my transmission. 1996 dodge stratus se 2.4 l


metal shavings is a good indicator the trany needs rebuilt,( those metal shavings are from drive gears inside of trany)but the only way to know 100% is to take it in. sorry that happened to you....i know that's not the answer you where looking for.

Sep 28, 2010 | 1996 Dodge Stratus

2 Answers

94 Grand Prix 3.1-Car won't go into any gear? It starts and runs and it even sounds like the shift lever is moving properly. The transmission is pretty new and we just recently rebuilt the engine and it...


first thing is to make sure trany fluid is full,start engine and check while in park,if oil level is good then i would have to say trany is bad,usually the motors are pretty good,those cars are famous for trany problems take it to a trany shop and have it checked out. good luck.

Nov 01, 2009 | 1994 Pontiac Grand Prix

1 Answer

2003 pontiac slips on 2-3 shift and does not down shift all the


who ever rebuilt trns missed something poss pcs solenoid, seals leak in input housing,seals or support housing leak,worn valvle in valve body, did he clear shift adapts, did he check for codes, did he do a press check, did he flush cooler nice trns overhaul good thing you got a warranty on job

Aug 25, 2009 | 2001 Pontiac Grand Prix

1 Answer

Intermitten hard shift 1-2, 2-3, flare shift into 4th


The trani is electronically controlled. without a diagnostic computer you are not going to know. It may be the speed sensors (for the trani.) but thats a guess. how long since the last trani service. Fluid level and condition can affect its perfomance. Good luck.

Apr 29, 2009 | 2003 Acura 3.2TL

2 Answers

K-5 blazer trany will not come out of first gear what is the porb


i used to have an 85 k-5 and it did that mine was the fuel filter but it could be the transmission filter our moudule the fuel filter is the cheepest and easiest thing to try first. good luck hope this fixes your prob.

Dec 18, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
1996 Dodge Dakota Logo

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...