Question about 2000 Chevrolet Blazer

1 Answer

Fuel pump went bought new one connectors are the same am i screwed or do they make a conversion kit?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

I would use a ac delco or delphi pump. with these parts at the cheap parts stores you dont want to do this more than once. you want to buy a complete module.

Posted on Sep 25, 2009

Testimonial: "thank you got the entire module now i just got to put it in thank you again"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace fuel pump 1993 mazda 323



REMOVAL & INSTALLATION

323, Protege, 520-22 626 and MX-6 and 522-24 MX-3 Models
See Figures 1 and 2

  1. Relieve the fuel pressure and disconnect the negative battery cable.
  2. If not already removed, depress the clips on each end of the rear seat cushion and remove the cushion.



0900c152802612b0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Detach the fuel hoses and electrical connections from the fuel pump, then remove the attaching screws and the pump


0900c152802612b1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Exploded view of the fuel pump assembly for the 323, Protege, 520-22 626, MX-6 and 522-24 MX-3

  1. If not already done, detach the electrical connector from the fuel pump/sending unit.
  2. Remove the attaching screws from the fuel pump/sending unit access cover and remove the cover.
  3. Disconnect the fuel supply and return hoses from the fuel pump/sending unit.
  4. Remove the attaching screws and the fuel pump/sending unit from the fuel tank.
  5. Detach the sending unit electrical connector, remove the sending unit attaching nuts and remove the sending unit from the fuel pump assembly.

To install:
  1. Attach the sending unit to the fuel pump assembly and install the nuts. attach the sending unit electrical connector.
  2. Install the fuel pump/sending unit into the fuel tank with a new gasket and install the mounting screws.
  3. Connect the fuel supply and return lines.
  4. Install the access cover and the mounting screws.
  5. Attach the sending unit electrical connector.
  6. Position the rear seat cushion over the floor, making sure to align the retaining pins with the clips. Push down firmly until the two retaining pins are locked into the rear seat retaining clips.
  7. Connect the negative battery cable, start the engine and check for proper system operation and for fuel leaks.

May 08, 2012 | 1993 Mazda 323

1 Answer

My aunts 1997 Jimmy was towed to my Dads .Cranks but no start,after batt. charged. They had been hitting bottom of fuel tank,and would start.But not anymore . Dad replaced pump.Had to rewire connectors for...


I would recommend checking the "re-wire job and make sure it is done correctly. Many GMs have had problems with the connectors at the fuel pumps. The fuel pump manufacturers have re-designed the connector to correct the problems they have been having. This is WHY the re-wire is required. The fuel pump kits usually come with the new connector to complete the job. However, some of the kits have wire colors that do not match the wire colors on the vehicle harness, Some of them also have "duplicate" colors, like two black wires. One will be a larger gauge than the other one. I had a couple where the white wire on the new connector had to be wired to the purple wire on the vehicle harness, etc. If your dad did not follow the directions EXACTLY then this could be the cause of your problem. (The pump MAY be running backwards)

Aug 03, 2011 | 1997 GMC Jimmy

1 Answer

1992 chevy blazer 4.3 vortec engine 2w dr have change the fuel pump fuel filter spark plugs rotor in the distributing cap ignition coil.and still doesnt want to start only cranks but doesnt stay on.


Check the wireing to the pump they had problems with it it tended to over heat and corroad there is a service bulliton on the prroblem #25215705and a kit with new wires and connector to resist over heating Icould give you the kit # but i got a DELPHI pump and the connector dosn;t fit a chevy pump

Nov 23, 2010 | 1994 Chevrolet S-10 Blazer

2 Answers

How can I take off the fuel pump on my nissan altima 2001


The procedure is as follows:---
  • First of all get the fuel pressure released and then disconnect the negative battery cable .
  • The fuel pump can be seen by taking out the rear seat and removing the access cover. Unplug the fuel pump's electrical connection and disconnect the fuel lines from the fuel pump. Remove the locking ring or screws with a socket wrench and disconnect the fuel gauge assembly so that you can disconnect the fuel tube from the fuel gauge.
  • Remove the fuel pump by holding the connector for the fuel line in one hand while pressing down on the two locking tabs at the same time. Lift the fuel pump out of the fuel tank. Discard the O-ring.
  • Install the new fuel pump using the items included in the kit, especially the O-ring. If you have a threaded lock ring, torque it to between 22 and 26 ft. lbs. If you have lock ring with six retaining screws, torque them to between 18 and 22 in. lbs.
  • Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

    Aug 19, 2010 | 2001 Nissan Altima

    1 Answer

    Sometimes it cranks and sometimes not. it finally went dead while idling. Cannot crank. Changed fuel pump and strainer. Cranked fine for two days and same thing happened. After I changed the fuel pump. The...


    Did you replace the fuel filter along with the fuel pump? You may have damaged the low fuel indicator when replacing the pump but as you stated, the main issue is a no start condition. Make sure that the ground wire for the pump is screwed down tight on a clean surface and make sure the wire and connector is good. It is the wire connected to one of the four screws that hold down the access plate (under the carpet behind the rear seat) to the fuel pump. Also, check the seal around the plate that is held in by the small screws(12 or 15 of them). Check for loose screws. Replace the fuel filter and remove the inlet side toward the rear. Fasten the line into a 2 litre soda bottle then crank the engine and watch to see if gas is coming out of the line. If no, you may have a new faulty pump. Hope that helps.

    May 07, 2010 | 2001 Kia Sportage

    2 Answers

    2001 express van fuel guage doesnt work


    SOUND LIKE FUEL GAUGE IS FAULTY.IF YOU REPLACED FUEL PUMP ASSEMBLY WITH NEW FUEL LEVEL SENDING UNIT.PROBLEM IS IN THE GAUGES.

    Mar 24, 2010 | Chevrolet Express Cars & Trucks

    1 Answer

    Change fuel filter on 1994 celica


    1994 Toyota Celica 1.8L EFI DOHC 4cyl
    The Fuel Filter is located under hood, center, upper firewall, mounted in fuel line.

    Common fuel line routing
    8e18bc1.gif


    View of the common electric fuel pump located under the rear seat
    3a8ebd2.gif


    Removal Fuel Pump

    1. Disconnect the negative battery cable.
    1. Remove the rear seat cushion.
    2. Unscrew the service hole cover.
    1. Disconnect the electrical fuel pump wiring at the pump assembly. Check for any fuel leakage while in there.
    1. Remove the gas cap, this will prevent any fuel gas spilling out of any high pressure lines.
    2. Using SST 09631-22020 or an equivalent line (flare nut) wrench, disconnect the outlet pipe from the pump bracket.
    1. Remove the pump bracket attaching screws.
    2. Disconnect the return hoses from the pump bracket, then pull out the pump/bracket assembly.
    1. Remove the nut and spring washer, then disconnect the wires from the pump bracket.
    1. Remove the sending unit attaching screws, then pull the unit from the bracket. To disassemble:
      1. Remove the lead wire.
      2. Pull the lower side of the fuel pump from the bracket.
      3. Remove the rubber cushion from the pump.
      4. Disconnect the hose from the pump and extract the pump.
      5. Separate the filter from the pump. Use a small screwdriver to remove the attaching clip.
      6. To remove the sender, disconnect the wiring from the bracket and unscrew the sender. Remove the screws, connector support, connector and gasket.
    2. Inspect all of the lines, hoses and fittings for any sign of corrosion, wear or damage to the surfaces. Check the pump outlet hose and the filter for restrictions.
    3. When reassembling, ALWAYS replace the sealing gaskets with new ones. Also replace any rubber parts showing any sign of deterioration.
    To install:
    1. To assemble the pump:
      1. Secure and install a new gasket, connector and support with the screws.
      2. Attach the sensor and secure the screws, connect the wiring to the pump bracket.
      3. Install the pump filter using a new clip.
      4. Connect the outlet hose to the pump.
      5. Install the rubber cushion to the fuel pump. Push the lower side of the pump into place to secure on the bracket.
      6. Engage the connector to the fuel pump.

    2. Install the fuel sending unit to the pump bracket.
    3. Install the fuel pump and bracket assembly onto the tank. Use new gaskets. Tighten the pump bracket retaining screws to 31 inch lbs. (3 Nm).
    1. Connect the return hoses to the pump bracket.
    2. Install the service hole cover, then the engage the fuel pump and sending unit connector.
    3. Connect the negative battery cable
    4. Start the engine and check carefully for any sign of leakage around the tank and lines. Road test the vehicle for proper operation.
    5. Install the rear seat cushion.
    I hope helps whit this (remember rated this help) Good luck.

    Dec 17, 2009 | 1994 Toyota Celica

    1 Answer

    My fuel pump went and i bought a new one but the connectors are n


    There is a fuse, but there is also a relay. They are both located in the fuse box under the hood. try the relay first before you condem the pump, its way easier to change, and alot cheaper.

    Sep 25, 2009 | 2000 Chevrolet Blazer

    1 Answer

    How do i replace the fuel pump in my 1993 mazda 626 2.5


    1. Relieve the fuel pressure and disconnect the negative battery cable.

    2. If not already removed, depress the clips on each end of the rear seat cushion and remove the cushion.

    3. If not already done, detach the electrical connector from the fuel pump/sending unit.

    4. Remove the attaching screws from the fuel pump/sending unit access cover and remove the cover.

    5. Disconnect the fuel supply and return hoses from the fuel pump/sending unit.

    6. Remove the attaching screws and the fuel pump/sending unit from the fuel tank.

    7. Detach the sending unit electrical connector, remove the sending unit attaching nuts and remove the sending unit from the fuel pump assembly.



    To install:

    1. Attach the sending unit to the fuel pump assembly and install the nuts. attach the sending unit electrical connector.

    2. Install the fuel pump/sending unit into the fuel tank with a new gasket and install the mounting screws.

    3. Connect the fuel supply and return lines.

    4. Install the access cover and the mounting screws.

    5. Attach the sending unit electrical connector.

    6. Position the rear seat cushion over the floor, making sure to align the retaining pins with the clips. Push down firmly until the two retaining pins are locked into the rear seat retaining clips.

    7. Connect the negative battery cable, start the engine and check for proper system operation and for fuel leaks.

    Jun 13, 2009 | 1993 Mazda 626

    Not finding what you are looking for?
    2000 Chevrolet Blazer Logo

    Related Topics:

    104 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8210 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...