Question about 1990 Jeep Wrangler

2 Answers

I'm getting no spark from ignition coil. I replaced the coil and still no spark. 1990 jeep wrangler 4 cyl

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

As I did find this quite helpful you should be ready for a bit of frustration when trying to acsess the CPS, be shure you are equiped with ample extentions as well as jack stand's and a second pair of hands never hurts.

Posted on Mar 22, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Does the coil have power?? if so, I would highly suspect the crank position sensor. its located back behind the engine drivers side, in the bell housing. its just a guess....... you are there, and I am here. Dont replace anymore parts till you know what is bad, I dont want you spending money on parts you dont need. you will need a wiring diagram, scanner and a service manual to properly diagnose this. a speed sensor or cam sensor could be shorted. take a voltage reading at the crank sensor ORANGE WIRE should be approx 5V if its not 5V disconnect the speed sensor ck again.. if its not 5V disconnect the cam sensor. when all these are disonnected you should have 5v if you do, then take a reading with them all hooked up should still be 5V. the thing I am trying to test is if one of these 3 sensors is shorted. by process of elimination one may be. good luck.

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Jeep YJ with no spark


try a new coil.some times a new coil will fail

Jul 29, 2012 | 1990 Jeep Wrangler

1 Answer

I have a 1990 Jeep Wrangler 4.2 6Cly manual, with no spark. There seems to be four things that could be the problem, trying to narrow it down. Ignition switch, ignition Module, Ignition Coil, or...


Hi, You're on the right track, just check those out. Check the distributor cap it could have a crack in it too. If you're not getting any spark than it would be the ignition module. Have you had any codes from the computer this will narrow it down to 1 or 2 items. Good luck.

Nov 22, 2011 | 1990 Jeep Wrangler

1 Answer

1988 Jeep Wrangler starting problems. I replaced the ignition module, spark plug wires, coil, distributor module, and my jeep will not start. It gets fuel, turns over, but still not starting. It is a 1988...


you are saying it is getting spark, and fuel, right? If it is getting spark, and fuel in to the throttle body, check compression-make sure the Mass Air Flow sensor is plugged in, and double check your spark-you say you replaced all those ignition items, but do not say that you have spark.

Jul 01, 2011 | 1988 Jeep Wrangler

1 Answer

How to repair fuel injector and timeing chain


get a haynes manual at a discount place or search online

May 26, 2010 | 1990 Jeep Wrangler

1 Answer

I have a 1990 4 cyl jeep wrangler i just filled tank with gas drove 1 block and jeep stalled. Jeep starts right back up but will not stay running seems as though its not getting enough gas. Is this a fuel...


if you just filled up i might be dirty fuel go get some fuel injector cleaner stp is good, lucas is better dump in your tank and cross your fingers you might have to start up a couple times.

May 15, 2010 | 1990 Jeep Wrangler

1 Answer

No spark from ignition module on hot start


95 JEEP WRANGLER 4 CYL

No spark. I have changed out the distributor cap, rotor, wiring from coil to cap, and coil was replaced. I checked the distibutor by turning ignition key and observing the rotor turn. What else can I check. I did not observe a module.

Jun 19, 2009 | 1995 Jeep Wrangler

3 Answers

1990 Jeep YJ 6 cyc. Won't Start---No Spark From Coil


It would be great if you could find the Ignition Control Module!!! From my experience on my Jeep...90 YJ 4.2 liter carb. it does not have one...Computer controlled only...

May 17, 2009 | 1990 Jeep Wrangler

1 Answer

No spark on my 1987 jeep wangler 6 cyl.


there is a timing sensor on driver side of tranny underneath near the top. if it is bad then you will not get it to start also the same on 4.0 Jeep cherokee

Apr 20, 2009 | 1990 Ford F150

Not finding what you are looking for?
1990 Jeep Wrangler Logo

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...