Question about 1999 Daewoo Nubira

Open Question

Installing and removing timing belt on a 1999 daewoo nubira

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
shanat
  • 359 Answers

SOURCE: i have replaced broken timing

did the timing belt snapbefore you replaced it? if so you may have bent some valves. if not recheck timing marks and distributor position.

Posted on Jul 06, 2008

Ad
  • 1 Answer

SOURCE: replacing timing belt on daewoo nubira 2000 model

Instructions Difficulty: Moderate Things You’ll Need:

  • Set of ¼-inch drive sockets ¼-inch drive ratchet Set of ½-inch drive sockets ½-inch drive ratchet Set of 3/8-inch drive sockets 3/8-inch drive ratchet Set of metric wrenches Floor jack Jack stands
Step1 Raise and support the vehicle on jack stands. Remove the intake air temperature wiring, the breather hose and intake air hose. Take off the air cleaner assembly. Step2 Remove the right wheel. Remove the accessory belts. Remove the crankshaft bolt and the crankshaft pulley. Remove the power steering bolts and the timing belt covers. Temporarily install the crankshaft bolt and turn the engine clockwise until the mark on the crankshaft pulley, which is a triangle stamped into the crank sprocket, is aligned with the corresponding triangular mark on the block. Step3 Make sure that the timing marks are aligned on the camshaft sprockets. These are a line on each sprocket that runs through a tooth on each sprocket. These lines should line up in the middle between each sprocket and point toward each other. If they do not line up, turn the crankshaft one more time and they will line up. It takes two turns of the crank to one complete revolution of the cam. Step4 Loosen the water pump bolts; using the 3/8-inch ratchet, turn the water pump clockwise away from the belt and loosely tighten the bolts to keep it there. Remove the timing beltmag-glass_10x10.gif. Make sure the timing marks are aligned and install the new belt starting on the right side from the crank sprocket and working counterclockwise. Keep all the belt tension on the right side away from the tensioner. Step5 Loosen the bolts in the water pump and rotate the water pump counterclockwise to apply tension to the belt. Watch the tensioner, which is above the water pump, and apply tension with the water pump until the pointer on the tensioner lines up with the notch above it. Lightly tighten the water-pump bolts. Step6 Turn the engine two more times and align the timing marks perfectly. Loosen the water-pump bolts and, using the ratchet, apply tension to the belt until the tensioner pointers are aligned. Tighten the water-pump bolts. Step7 Install the timing-belt covers and the bolts in the power-steering pump and tighten. Remove the crankshaft bolt and install the crank pulley and the bolt, then torque the crankshaft pulley bolt to 70 foot pounds of torque. Install all components in reverse order of removal.

Posted on Mar 08, 2009

  • 1 Answer

SOURCE: how do i change the camshaft sensor on a 1999 daewoo nubira?

read all of this before you begin! you may be able to skip a step that i couldnt !no.you dont have to remove the timing belt but check it. i did this to my nubira like two months ago. the belt felt loose but i didnt change it and now my car is on the side of the road) remove breather box. remove spark plug cover(top of engine two allen screws).see cam pos sen. wire clip at front of engine facing down, dont try to remove yet. clips are at the top sides of timing belt cover. from under the car remove plastic covers where you may find them on the pulley side and passenger side wheel well. using socket wrench relieve tension on torsion wheel(smallest pulley your s-belt crosses) by pushing up. release s-belt and remove(you may want to draw a quick diagram of how your belt is ran before removing). now remove the bolts from the timing belt cover.(when i did this i was also changing my harmonic balancer or crank pulley,if it is in the way of bolts remove the four bolts with a allen wrench,loosen it with the s-belt still on and car in fifth gear if standard to keep crank from turning. next place a long board or plank under the engine (across trans-housing,oil pan, as little on the oil pan as possible . place a jack at the center of the board and gently raise the engine. this relieves pressure from the top engine mount. remove the engine mount entirely. remove all screws from timing belt cover. remove cover. you will see two camshft gears at the top of the engine just below them you will see one star head screw(can usually be removed with an alle n wrench). it hold the cam pos sensor in place, remove then pull sensor out the top of the motor. sometimes they're a little bit stuck down in there. just pry a little but dont pull on wires! once removed disconnect wire replace, and rebuild. hope this helps

Posted on Jul 19, 2009

  • 19 Answers

SOURCE: How to set a ignitin timing on 1999 daewoo nubira CDX

timing on modern cars is computer controled and cant be changed, unless computer is reflashed.

Posted on Feb 27, 2010

  • 1757 Answers

SOURCE: replacing timing belt on daewoo nubira 2000 model

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/2000/make/daewoo/model/nubira/2000_daewoo_nubira_timing_belt_diagram_marks.htm

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Daewoo nubira 2002


Please follow this link to the see the whole process with diagrams of the belt change. Please note if the belt broke you likely have bent valves.

Oct 17, 2012 | 1999 Daewoo Nubira

1 Answer

1999 daewoo nubira serpentine belt routing


The diagram you requested is below and thank you for using Fixya!
Greg

1999 Daewoo Nubira


10_8_2011_6_50_34_pm.jpg

Oct 08, 2011 | 1999 Daewoo Nubira

1 Answer

Timing belt route


Check this image about Belt Routing;Serpentine (years: 1999-2000)...

zjlimited_728.jpg


Additionaly if you are interesting, in this link could find the Nubira's manual: Daewoo/Nubira/Nubira%20complet

Hope this helps.

Feb 21, 2011 | 2000 Daewoo Nubira

1 Answer

ON MY 1999 DAEWOO NUBIRA I HAVE AN OIL LEAK DOWN BY THE OIL FILTER BEHIND THE LOWER REAR TIMING BELT COVER.IT SPRAY OUT IN A SMALL STREAM WHEN EVER I CRANK THE CAR.


possibly oil pressure switch which has one wire going to it near oil filter or split oil pump gasket or crank seal, might have to remove timming belt cover and crank while cover is off to locate leak

Jan 24, 2011 | 1999 Daewoo Nubira

1 Answer

How do i replace the camshaft sensor on a 1999 daewoo nubira? do i have to take the timing belt off?


no dont need to take belt off if its twin cam by the sound of things
just top bolt which is inside cam belt cover remove top cam cover retainer clip in top centre if still there and then 10mm bolt in cam belt cover just down from top middle section of cover bend gently to get to cam sensor bolt if have too much trouble doing this whole cam belt cover needs removing, air box, accessory drive belt and engine mount will need jack to support engine and to reinstall mount

Jun 27, 2009 | 1999 Daewoo Nubira

1 Answer

Where is the camshaft sensor located at on a 1999 daewoo nubira?


remove eng cover. it is at the front of eng neer timing belt, to re place timing belt must come off good luck

Jun 25, 2009 | 1999 Daewoo Nubira

1 Answer

Daewoo nubira timing marks


no timing marks on cover, timing marks are on sprokets they should be lined oposite each other.

Jan 17, 2009 | 1999 Daewoo Nubira

1 Answer

Timing marks for a daewoo nubira cdx


Here is a pic if the timing marks two small marks on the cam pulleys and one small cut away on the crank pulley .
3d2c66e.png

Dec 14, 2008 | 1999 Daewoo Nubira

2 Answers

Need a picture diagram of 1999 daewoo Leganza timing belt setting or mars?


need a picture diagram for timing marks nubira 2001 2.0L

Jul 20, 2008 | 2002 Daewoo Nubira

1 Answer

I have replaced broken timing belt on 1999 daewoo nubira and all timing marks line up but it will not idle properly and knocks


did the timing belt snapbefore you replaced it? if so you may have bent some valves. if not recheck timing marks and distributor position.

Jul 06, 2008 | 1999 Daewoo Nubira

Not finding what you are looking for?
1999 Daewoo Nubira Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...