Question about 1998 Chevrolet K1500

1 Answer

Bolts on exhaust are stuck, how do you get them broke free?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 490 Answers

Soak them with pb blaster and use impact or air ratchet to loosen them

Posted on Sep 25, 2009

Testimonial: "This was a great tip! I did not know of such great solution. Those bolts made a loud bang when they broke with help of that solution. Good Job! Expert"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It sounds lk a manifold leak or something on the right side and I can't find out if that's it or not


Ticking and goes away? exhaust manifold leak. Most times a bolt broke. You can find it. Look for black spots around the exhaust and engine.

Apr 10, 2016 | 1998 Land Rover Range Rover

1 Answer

I just replaced the exhaust system in my 91 tercel but in 3rd and 4th gear it seems like it is stuck help


It sounds to me like you damaged or broke the linkage from the shift lever to the transmission. Take a look at the linkage and see if anything is loose or stuck. if not, then these 2 issues (exhaust being replaced, tranny not shifting) are not likely related.

May 08, 2014 | Cars & Trucks

2 Answers

Diagram to locate starter on 2002 miysubishi galant?


The starter motor is located on the front of the engine behind the exhaust pipe and next to the oil filter.

First disconnect the battery. Next remove the flat, angular heat shield from the starter itself (1x 8mm nut and 2x 8mm bolts). Do NOT try to remove the heat shield from the Exhaust pipe - it can't be removed with the starter in place and it's not necessary anyway. Next remove the oil filter. You'll loose a few ounces of oil so be prepared for that with a drain pan and either cover the removed filter to keep debris out or replace it and remember to check the oil level later. Remove the small signal wire from the solenoid (released by pushing in a tiny lever with a finger tip) and also remove the 12mm nut attaching the positive battery cable to the starter.

The starter is held in place by two 14mm bolts. On the engine (passenger) side, there is a 14x30mm bolt threading into the transaxle from the bottom of the starter. On the transaxle (driver) side, there is a longer 14x50mm bolt threading into the top of the starter


sorry i couldnt find an actual diagram for ya, hope this helps

Apr 03, 2011 | 2002 Mitsubishi Galant

1 Answer

How to replace a waterpump on a 2001 olds alero 2.4 cam


Water pump is driven by timing chain idler and is mounted on the rear of the timing chain housing. Disconnect the neg. battery cable. Drain cooling system. Disconnect oxygen sensor connector.
Remove upper exhaust manifould heat sheild. Remove exhaust manifold brace. Remove lower exhaust manifold heat sheild. Loosen manifold to exhaust manifold spring loaded nuts. Remove radiator outlet pipe to water pump coverbolts. Disconnect exhaust pipe from manifold.
Pull down on the exhaust pipe to disconnect it from exhaust manifold bolts. Disconnect outlet pipe from oil pan and transaxle. If equipped with manual tranaxle, remove exhaust maifold brace. Leave lower radiator hose attached and pull down on radiator out look pipe to disengauge from water pump. Leave outlet pipe hanging.
Lower vehicle. Remove exhaustmanifold to cylinder head nuts. Remove exhaust manifold to cylinder head nuts. Remove manifould. Remove timing chain front cover. Remove timing chain tensioner. Remove bolts bolts securing water pump cover to cylinder block. Remove water pump to timing chain housing nuts. Remove water pump attaching nuts. Remove water pump and cover assembly. Separate componets as necessary.
WHEN INSTALLING WATER PUMP MAKE SURE YOU FOLLOW THE TIGHTENING SEQUENCES THAT AFFECT SEALING. My frist one I messed up and broke the pump so becarful.
Installation
If cover was separated from body during removal, join this componets with a new gasket and hand tighten bolts. Apply bearing grease to splines of water pump drive. Set body and assemble into position.
Install and hand tighten bolts securing cover to cylinder block. Install and hand tighten bolts securing cover to cylinder block. Installand hand tighten nuts securing body to timing chain housing. Lubracate outlet pipe "O" ring with antifreeze. (I use RTV) Connect outlet pipe. Install and hand tighten bolts. Tighten bolts and nuts to specification in the following sequence. I'll ad the torque spec. at the end but this is where if you tighten out of order something will break.
pump assembly to timing chain housing nuts.
pump cover to pump body bolts
pump cover to cylinder block bolts (Bottom Bolt First)
outlet pipe to cover bolts
To complete installation reverse removel procedure.
Torque specs are 19 in. or 26mm all except water pump cover bolts which are 124 in or 14Nm
I never torque the bolts just make sure there done in the right order.

Oct 19, 2010 | Oldsmobile Alero Cars & Trucks

1 Answer

The head broke off and the bolt is stuck


you must center punch the center of bolt and drill a hole right in center of busted bolt, then get an ez- out from auto parts store and remove it then replace with new bolt with correct length and thread count, any more help please let me know

Mar 23, 2010 | 2006 Chevrolet Cobalt

2 Answers

How to remove starter from 1991 acura legend


Follow the battery wire (disconnected) to the starter and remove the nut and solenoid wire. There should be two bolts to the bellhousing (a old term for the transmission to engine piece).

Aug 18, 2009 | 1991 Acura Legend

Not finding what you are looking for?
1998 Chevrolet K1500 Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...