Question about Mercedes-Benz C-Class

Open Question

Can anyone help me with MB manual instructions (scanned in and emailed to me at migomiconi@yahoo.com)on how to remove lower left knee panel below steering wheel?

Posted by on

  • migomiconi Sep 28, 2009

    Where is the solution printed? How do I access the solution from Parika? Thank you.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Mode Actuator Located in a 2008 Pontiac G6?


Preliminary Procedure
Remove the instrument panel left outer trim panel. Refer to Instrument Panel Outer Trim Cover Replacement .
Remove the left closeout/insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Left Side .
Remove the data link connector.
1
Screws, Knee Bolster (Qty: 3)
Tighten
2 N·m (18 lb in)
2
Knee Bolster Assembly
3
Retaining Clip, Knee Bolster (Qty: 3)

Callout
Component Name
Notice: Refer to Fastener Notice in the Preface section.
Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .
1
Screw, Instrument Panel Closeout/Insulator (Qty: 2)
Tighten
2 N·m (18 lb in)
2
Nut, Instrument Panel Closeout/Insulator (Qty: 1)
Tighten
2 N·m (18 lb in)
3
Panel Assembly, Instrument Panel Closeout/Insulator

Removal Procedure
Remove the fuse labeled HVAC CTRL (BATT).
Remove the left closeout panel. Refer to Instrument Panel Insulator Panel Replacement - Left Side .
Remove the knee bolster. Refer to Knee Bolster Replacement .
Remove the mode actuator retaining screws.
Remove the mode actuator.
Disconnect the mode actuator electrical connector.

Nov 22, 2016 | Pontiac Cars & Trucks

5 Answers

4-WAY FLASHERS


Sir,

The combination flasher unit for the turn signals and hazard flashers is located to the left of the floor console behind the lower steering colum trim cover.

Thanks
good luck

gaframe = true; ' + '' + google_ads[i].line1 + '
' + '' + google_ads[i].line2 + ' ' + google_ads[i].line3 + '
' + '' + google_ads[i].visible_url + '
'; } } var adsByGoogleRight = "-40px"; if(dartRecieved){ document.getElementById("ga_300x250").style.clear="both"; document.getElementById("ga_300x250").style.left = "0px"; document.getElementById("inner_adv_caption").style.display = "block"; adsByGoogleRight = "5px"; } else if(isHealthinationExist){ var healthinationBox = $('healthonationBox'); if(healthinationBox){ var helthinationBot = getObjXY(healthinationBox)[1]+healthinationBox.clientHeight; var ga_top =getObjXY(document.getElementById("ga_300x250"))[1]; if(ga_top-helthinationBot >0){ document.getElementById("ga_300x250").style.width = "530px"; } else{ document.getElementById("ga_300x250").style.width = "410px"; } } $('boxAdWrapper').style.display = "none"; } else{ document.getElementById("ga_300x250").style.width = "530px"; $('boxAdWrapper').style.display = "none"; } //add "ads by google" var logo_img = 'abg-en-100c-000000.gif'+versionno+''; s += '' + logo_img + ''; document.getElementById("ga_300x250").innerHTML = s; var currl = $('related_links'); var currq = $('related_questions'); if(currl!=null && currq!=null){ var currltop = getObjXY(currl)[1]; if(currltop > rltop ) currq.style.clear="left"; } return; }; //-->

Sep 21, 2008 | 1999 Audi A4

2 Answers

Is there any diagram or instructions to replace a heater core on a 2001 GMC Jimmy. If so where do I find it on the computer?


Please let me know if you have any questions, and thanks for using FixYa.

Removal:
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the engine cooling system.
  3. Remove or disconnect the following:
    Negative battery cable, Heater hoses from the heater core.
  4. Remove the instrument panel as follows:
    1. Disable the air bag system.
    2. Set the parking brake and block the wheels.
    3. Disconnect the parking brake release cable from the parking brake lever.
    4. Unfasten the screws that retain the DLC instrument panel left side sound insulator. Feed the DLC through the hole in the sound insulator.
    5. Unfasten the right side sound insulator panel screws and remove the panel.
    6. Unfasten the screws that attach the instrument panel left side sound insulator to the knee bolster and cowl panel.
    7. Unfasten the nut that attaches the left side sound insulator to the accelerator pedal bracket.
    8. Unplug the remote control door lock receiver module electrical connector.
    9. Remove the door lock receiver module from the left side sound insulator. Remove the left side sound insulator.
    10. Unfasten the screws that attach the instrument panel center sound insulator to the knee bolster, instrument panel, heater assembly and floor duct.
    11. Remove the center sound insulator.
    12. Unfasten the screws that attach the courtesy lamp to the knee bolster.
    13. Unfasten the screws that attach the knee bolster to the instrument panel.
    14. Disconnect the lap cooler duct from the knee bolster.
    15. Unplug the lighter electrical connection and remove the knee bolster.
    16. Unfasten the steering column-to-instrument panel nuts and lower the column.
    17. Unfasten the screws that attach the instrument panel accessory trim plate to the instrument panel.
    18. Remove the trim plate and unplug all necessary electrical connection.
    19. Remove the heater and/or air conditioning control assembly.
    20. Remove the radio and the storage compartment assembly (if equipped).
    21. If necessary, remove the instrument cluster.
    22. Unfasten the left and right instrument panel pivot bolts and the panel lower support bolt.
    23. Unfasten the speaker grilles retaining screws and remove the speaker grilles.
    24. Remove the windshield defroster grille using a flat-bladed prytool. Start at one end of the grille and work your way down the grille.
    25. Unfasten the 4 instrument panel upper support screws.
    26. Tag and unplug all necessary electrical connections.
    27. Remove the instrument panel from the vehicle.
  5. Remove or disconnect the following:
    Air inlet assembly, if equipped, Vacuum hoses, Heater assembly studs, from inside the engine compartment, Blower motor resistor, Stud from inside the heater case assembly; the stud is located behind the blower motor resistor, Heater assembly-to-chassis screws, Heater assembly from the vehicle, Access cover screws and cover from the heater assembly, Heater core from the heater case assembly.
    jturcotte_402.jpg

    Fig. View of the heater case assembly

    jturcotte_403.jpg

    Fig. View of the heater case cover

    jturcotte_404.jpg

    Fig. View of the heater core

    jturcotte_405.jpg

    Fig. Heater core mounting

To install:
  1. Install or connect the following:
    Heater core to the heater case assembly, Access cover to the heater assembly and the cover screws, Heater assembly to the vehicle, Heater assembly-to-chassis screws and torque them to 40 inch lbs. (4.5 Nm), Stud, working from inside the heater case assembly; the stud is located behind the blower motor resistor, Blower motor resistor, Heater assembly studs, working inside the engine compartment, torque them to 17 inch lbs. (1.9 Nm), Vacuum hoses, Air inlet assembly, if equipped
  2. Install the instrument panel as follows:
    1. Rest the instrument panel on the lower pivot studs.
    2. Attach the electrical connections.
    3. Install but do not tighten the 4 upper instrument panel support screws.
    4. Install the left and right panel pivot bolts. Tighten the bolts to 102 inch lbs. (11.5 Nm).
    5. Install the panel lower support bolt. Tighten the bolt to 102 inch lbs. (11.5 Nm).
    6. Tighten the upper support screws to 17 inch lbs. (1.9 Nm).
    7. Install the windshield defroster grille and the speaker grilles.
    8. Install the radio and storage compartment assembly (if equipped).
    9. If removed, install the instrument cluster.
    10. Install the heater and/or air conditioning control assembly.
    11. Attach the electrical connections to the instrument panel accessory trim plate.
    12. Place the trim plate in position and install its retaining screws. Tighten the screws to 17 inch lbs. (1.9 Nm).
    13. Place the steering column into position and install its retaining nuts. Tighten the nuts to 22 ft. lbs. (30 Nm).
    14. Attach the lighter electrical connection and the lap cooler duct to the knee bolster.
    15. Place the knee bolster into position and install its retaining screws. Tighten the Torx® head screws to 80 inch lbs. (9 Nm) and the hex head screws to 17 inch lbs. (1.9 Nm).
    16. Place the courtesy lamp in position and install its screws. Tighten the screws to 17 inch lbs. (1.9 Nm).
    17. Place the instrument panel center sound insulator in position. Install the screws that attach the center sound insulator to the knee bolster, instrument panel and the floor duct. Tighten the screws to 17 inch lbs. (1.9 Nm).
    18. Install the screw that attaches the center sound insulator to the heater assembly. Tighten the screw to 13 inch lbs. (1.5 Nm).
    19. Install the remote control door lock receiver module to the instrument panel left side sound insulator.
    20. Attach the door lock receiver electrical connection.
    21. Install the nut that attaches the left side sound insulator to the accelerator pedal bracket. Tighten the nut to 35 inch lbs. (4 Nm).
    22. Install the screw that attaches the left side sound insulator to cowl panel. Tighten the screw to 13 inch lbs. (1.5 Nm).
    23. Install the screws that attach the left side sound insulator to knee bolster. Tighten the screw to 17 inch lbs. (1.9 Nm).
    24. Feed the DLC through the hole in the sound insulator, place the DLC in position and install its retaining screws. Tighten the screws to 21 inch lbs. (2.4 Nm).
    25. Install the right side sound insulator and tighten the screws
    26. Connect the parking brake release cable to the lever.
    27. Enable the air bag system.
  3. Install the heater hoses to the heater core.
  4. Refill the cooling system.
  5. Connect the negative battery cable.
  6. Run the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Apr 04, 2011 | 2001 GMC Jimmy

1 Answer

How to change heater core on 2005 dodge stratus?


  1. Disconnect the negative battery cable.
  2. Remove the radio/HVAC control module bezel. CAUTION
    The vehicles covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses air bags. Whenever working near any of the SRS components, such as the impact sensors, air bag modules, steering column and instrument panel, disable the SRS, as described earlier in this section.
  3. Remove the right instrument panel side trim.
  4. Remove the two retaining screws at the lower right side support beam.
  5. Remove the instrument panel support bolt at the A-pillar.
  6. Remove the left instrument panel side trim and upper instrument panel bezel.
  7. Remove the lower knee bolster and console screws at the instrument panel.
  8. Remove the gearshift knob and shifter bezel.
  9. Remove the mounting screws at the front and rear of the floor console. Remove the front and rear console halves.
  10. Remove the right side instrument panel support strut.
  11. Drain the cooling system into a suitable container, then disconnect the heater hoses at the cowl panel. Plug the heater core outlets to prevent coolant from spilling during unit housing removal.
  12. Remove the mounting screws and heater core cover.
  13. Remove the heater core from the vehicle. To install:
  14. Carefully position the heater core unit into the heater housing.
  15. Install the heater core cover onto the heater housing and tighten the mounting screws.
  16. Install the right side instrument panel support strut.
  17. Install the front and rear console halves.
  18. Install the shifter bezel and gearshift knob.
  19. Install the lower knee bolster and console screws at the instrument panel.
  20. Install the upper instrument panel bezel and left instrument panel side trim.
  21. Install the instrument panel support bolt at the A-pillar.
  22. Install the two retaining screws at the lower right side support beam.
  23. Install the right instrument panel side trim.
  24. Install the radio/HVAC control module bezel.
  25. Fill the cooling system to the proper level.
  26. Connect the negative battery cable.

Aug 13, 2010 | 2005 Dodge Stratus

1 Answer

I need to know how to do the heater core in a chevy s10 p/u


  1. Disconnect the negative battery cable.
  2. Drain the engine cooling system.
  3. Remove or disconnect the following:
    • Heater hoses from the heater core
  4. Remove the instrument panel as follows:
    • Disable the air bag system.
    • Set the parking brake and block the wheels.
    • Disconnect the parking brake release cable from the parking brake lever.
    • Unfasten the screws that retain the DLC instrument panel left side sound insulator. Feed the DLC through the hole in the sound insulator.
    • Unfasten the right side sound insulator panel screws and remove the panel.
    • Unfasten the screws that attach the instrument panel left side sound insulator to the knee bolster and cowl panel.
    • Unfasten the nut that attaches the left side sound insulator to the accelerator pedal bracket.
    • Unplug the remote control door lock receiver module electrical connector.
    • Remove the door lock receiver module from the left side sound insulator. Remove the left side sound insulator.
    • Unfasten the screws that attach the instrument panel center sound insulator to the knee bolster, instrument panel, heater assembly and floor duct.
    • Remove the center sound insulator.
    • Unfasten the screws that attach the courtesy lamp to the knee bolster.
    • Unfasten the screws that attach the knee bolster to the instrument panel.
    • Disconnect the lap cooler duct from the knee bolster.
    • Unplug the lighter electrical connection and remove the knee bolster.
    • Unfasten the steering column-to-instrument panel nuts and lower the column.
    • Unfasten the screws that attach the instrument panel accessory trim plate to the instrument panel.
    • Remove the trim plate and unplug all necessary electrical connection.
    • Remove the heater and/or air conditioning control assembly.
    • Remove the radio and the storage compartment assembly (if equipped).
    • If necessary, remove the instrument cluster.
    • Unfasten the left and right instrument panel pivot bolts and the panel lower support bolt.
    • Unfasten the speaker grilles retaining screws and remove the speaker grilles.
    • Remove the windshield defroster grille using a flat-bladed prytool. Start at one end of the grille and work your way down the grille.
    • Unfasten the 4 instrument panel upper support screws.
    • Tag and unplug all necessary electrical connections.
    • Remove the instrument panel from the vehicle.
  5. Remove or disconnect the following:
    • Air inlet assembly, if equipped
    • Vacuum hoses
    • Heater assembly studs, from inside the engine compartment
    • Blower motor resistor
    • From inside the heater case assembly, the stud; the stud is located behind the blower motor resistor
    • Heater assembly-to-chassis screws
    • Heater assembly from the vehicle
    • Access cover screws and cover from the heater assembly
    • Heater core from the heater case assembly
dcf2340.gif
View of the heater case assembly

3e4f811.gif
View of the heater case cover

9d01ecc.gif
View of the heater core

Oct 19, 2009 | 2000 Chevrolet S-10

1 Answer

INSTRUCTIONS ON REMOVAL OF STOCK STEREO


1. REMOVE THE NARROW TRIM PIECES TO THE RIGHT AND LEFT OF THE RADIO TRIM PANEL.

2.REMOVE THE GLOVE BOX.

3. REMOVE THE KNEE BOLSTER UNDER THE STEERING COLUMN.

4. REMOVE THE I/P CENTER TRIM PANEL. LOOK FOR THE SCREWS ON THE LOWER EDGES OF THE TRIM PANEL. DISCONNECT THE HAZARD SWITCH.

5. REMOVE THE HVAC CONTROL MODULE.

6. REMOVE THE RADIO.

IF YOU ARE REPLACING A STOCK RADIO WITH ANOTHER STOCK RADIO IT MAY HAVE TO BE PROGRAMMED BEFORE IT WILL WORK.

IF THIS HELPED YOU PLEASE RATE ME.

Jul 04, 2009 | 2007 Chevrolet Malibu SS Sedan New Cars

1 Answer

I need to replace an ignition switch on my 1999 Chrysler Sebring convertible, how do I remove the dashboard


This is for the ignition switch like you are asking for:

Ignition Switch REMOVAL & INSTALLATION Cirrus, Stratus, Sebring Convertible and Breeze CAUTION
The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the steering column. Failure to do so may cause accidental deployment of the air bags, resulting in unnecessary SIR system repairs and/or personal injury.
  1. Disarm the air bag system, as described in Section 6.
  2. Remove the left end instrument panel cover/fuse panel and remove the retaining screw holding the end of the instrument panel top cover.
  3. Remove the instrument panel center bezel.
  4. Remove the screws that secure the instrument panel top cover to the center of the instrument panel.
  5. Lift the instrument panel top cover enough to gain access to the knee bolster attaching screws.
  6. Remove the lower knee bolster attaching screws and knee bolster from the vehicle.
  7. Remove the lower steering column cover attaching screws. Pull down on the lower cover to clear the ignition key cylinder and key release (if equipped).
  8. Remove the lower steering column cover, sliding the cover forward while holding down the steering wheel tilt lever.
  9. Tilt the steering wheel down to the fully lowered position and remove the upper steering column cover.
  10. Remove the screws that hold the combination switch to the ignition lock housing.
  11. Place the ignition lock cylinder in the RUN position.
  12. Insert a small prying tool into the hole in the lower cover and depress the cylinder release tab.
  13. Remove the ignition lock cylinder from the steering column.
  14. Unfasten the electrical connectors from the switch.
  15. Using a No. 10 Torx® bit, remove the ignition switch mounting screw.
  16. Depress the retaining tabs and remove the switch. To install:
  17. Place the ignition switch in the RUN position. Be sure the actuator shaft in the lock housing is also in the RUN position.
  18. Install the switch, making sure the switch snaps over the retaining tabs.
  19. Install the retaining screw.
  20. Connect the wiring to the ignition switch.
  21. Install the ignition lock cylinder.
  22. Install the 2 combination switch mounting screws.
  23. Install the lower and upper shrouds.
  24. Install the knee bolster to the lower dashboard panel and tighten the lower knee bolster attaching screws.
  25. Install the screws that secure the instrument panel top cover to the center of the instrument panel.
  26. Install the instrument panel center bezel.
  27. Install and tighten the screw holding the end of the instrument panel top cover. Install the left side instrument panel/fuse panel cover.
More coming.....

Jun 26, 2009 | 1999 Chrysler Sebring

1 Answer

My son recently bought a 3000GT SL but, the sunroof regulator assembly had been removed and disassembled. I have a box of parts, with definetly some screws missing but, I can only partially figure out how...


I may have a blow up in my service manual. If you haven't gotten it together, email me at OneRide2869@yahoo.com and I'll scan and email you the exploded diagram and instructions if my manual has them. BTW, an eBay seller, sphear_media, has 3000GT manuals on CD for around $10. You should get one. Trust me, you are gonna need it. I know, I own a 91 3000GT.

Apr 18, 2009 | 1995 Mitsubishi 3000GT

1 Answer

Pulled every thing apart to get the heater core out and I can't figure out how to get it out. What am I doing wrong??????


  1. Drain the engine cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Heater hoses from the heater core
  3. Remove the instrument panel as follows:
    1. Disable the air bag system.
    2. Set the parking brake and block the wheels.
    3. Disconnect the parking brake release cable from the parking brake lever.
    4. Unfasten the screws that retain the DLC instrument panel left side sound insulator. Feed the DLC through the hole in the sound insulator.
    5. Unfasten the right side sound insulator panel screws and remove the panel.
    6. Unfasten the screws that attach the instrument panel left side sound insulator to the knee bolster and cowl panel.
    7. Unfasten the nut that attaches the left side sound insulator to the accelerator pedal bracket.
    8. Unplug the remote control door lock receiver module electrical connector.
    9. Remove the door lock receiver module from the left side sound insulator. Remove the left side sound insulator.
    10. Unfasten the screws that attach the instrument panel center sound insulator to the knee bolster, instrument panel, heater assembly and floor duct.
    11. Remove the center sound insulator.
    12. Unfasten the screws that attach the courtesy lamp to the knee bolster.
    13. Unfasten the screws that attach the knee bolster to the instrument panel.
    14. Disconnect the lap cooler duct from the knee bolster.
    15. Unplug the lighter electrical connection and remove the knee bolster.
    16. Unfasten the steering column-to-instrument panel nuts and lower the column.
    17. Unfasten the screws that attach the instrument panel accessory trim plate to the instrument panel.
    18. Remove the trim plate and unplug all necessary electrical connection.
    19. Remove the heater and/or air conditioning control assembly.
    20. Remove the radio and the storage compartment assembly (if equipped).
    21. If necessary, remove the instrument cluster.
    22. Unfasten the left and right instrument panel pivot bolts and the panel lower support bolt.
    23. Unfasten the speaker grilles retaining screws and remove the speaker grilles.
    24. Remove the windshield defroster grille using a flat-bladed prytool. Start at one end of the grille and work your way down the grille.
    25. Unfasten the 4 instrument panel upper support screws.
    26. Tag and unplug all necessary electrical connections.
    27. Remove the instrument panel from the vehicle.
  4. Remove or disconnect the following:
    • Air inlet assembly, if equipped
    • Vacuum hoses
    • Heater assembly studs, from inside the engine compartment
    • Blower motor resistor
    • Stud from inside the heater case assembly; the stud is located behind the blower motor resistor
    • Heater assembly-to-chassis screws
    • Heater assembly from the vehicle
    • Access cover screws and cover from the heater assembly
    • Heater core from the heater case assembly

Feb 19, 2009 | 2001 GMC Jimmy

2 Answers

Needs number for fuse for front heater


Hi
It will be buy your left knee in the little fuse box
Paul

Dec 13, 2008 | 1996 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...