Question about 1992 Chevrolet Lumina

1 Answer

Sub frame connector its rubber with a bolt through it

Posted by on

  • Joseph Howard May 11, 2010

    What is it that you need help with?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Exhaust hanger.

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to lower front sub frame on 2002 mercury sable


support car place jack stands under sub frame. using an engine support to hold motor in place, disconnect anything that is attached to sub frame, ex: motor mounts. then unbolt sub frame bolts(4) and raise car to remove sub frame. note sub frame is heavy.

Jun 24, 2015 | Mercury Cars & Trucks

1 Answer

How to take transmission out


It is a pretty involving process to remove and replace the transmission on a Honda Odyssey and not recommended for the home DIY mechanic. Without a vehicle hoist or lift, it is a daunting task to undertake. This will be a brief description of what may need to be removed. The engine and transmission sits on a sub frame cradle. The engine will need to be held and supported by an engine support bar. The sub frame is then unbolted from the bottom. All things necessary must be removed before the sub frame can come out. For example, the rack and pinion bolts, sway bar, lower front ball joints, front and rear engine mounts, and any and all brackets and hard lines. After the sub frame is completely out, the flywheel bolts will have to be removed from the transmission. The cv-axles will have to be removed along with the transmission fluids being drained. Then the harness/connectors disconnected from the transmission, and then the bolts to the engine and bolts for the transmission mount. With a floorjack, the transmission can then be dropped out from underneath. Installation is the reversal.

Mar 13, 2015 | 2003 Honda Odyssey

1 Answer

How do I take a tranmission out of a 2004 Chev Impala(police car)


Hello: First you have to support the engine from the top, you have to raise car, remove sub frame after you remove wheels lines, electrical connectors wheels etc. After removing sub frame remove bolts holding converter to flywheel remove bolts holding transmission to the engine. (NOT A BEGINNERS JOB)

Have a transmission jack to hold the transmission when you take it loose from the engine.

Aug 12, 2011 | Chevrolet Impala Cars & Trucks

1 Answer

Replace broken sway bar for a 1996 ford windstar


Section 04-01: Suspension and Wheel Hubs, Front 1996 Windstar Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal
  1. Raise and support the vehicle. Refer to Section 00-02 .
  1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the 6 mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten or final tighten the front stabilizer bar link-to-shock absorber nut.
    Using care not to damage the front stabilizer bar link ball stud seal, remove the RH and LH front stabilizer bar link-to-front shock absorber nut.




  1. Using care not to damage the front stabilizer ball link stud seal, remove the RH and LH front stabilizer bar link-to-front stabilizer bar nut.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage the ball joint boot.
    With another set of support safety stands under front sub-frame, remove two rear sub-frame retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).
  1. Remove front stabilizer bar bracket bolts, stabilizer bar brackets, stabilizer bar bracket insulators and front stabilizer bar (5482) as required.
Installation
  1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar bracket insulator installation position.
  1. Lubricate inside diameter of new stabilizer bar bracket insulator with Rubber Suspension Insulator Lube E25Y-19553-A meeting Ford specification ESF-M99B112-A or equivalent. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber stabilizer bar bracket insulators.
  1. Install new stabilizer bar bracket insulators onto front stabilizer bar and position them in approximate location.
  1. Install stabilizer bar bracket on stabilizer bar bracket insulators and install new bolts. Tighten to 55-63 Nm (40-46 lb-ft).
  1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Tighten to 115-132 Nm (85-97 lb-ft).
  1. Install front stabilizer bar link (5K483) to front shock absorber. Use care not to damage link ball joint boot seal.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the 6 mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten or final tighten the front stabilizer bar link-to-shock absorber nut.
    Install a new front stabilizer bar link-to-shock absorber nut. Tighten to 90-100 Nm (66-74 lb-ft).

  2. 66a0f1a.gif

Apr 28, 2010 | 1996 Ford Windstar

1 Answer

Need diagram for 2003 PT Cruiser engine and ties to chasiss (what holds the engine to the body)


the engine and transmission are called a trans axle your vehicle is a uni body construction,however your engine and trans are mounted on a sub frame as an assembly and are a separate part of the vehicle,that is, when the vehicle is built the trans axle is on its own frame raised up into the vehicle and bolted in place.then the electrical,hoses,exhaust,brake lines,etc. are connected to the body from it. all of this is part of the front of the vehicle only. if you look under the front of your vehicle you can see the bolts that connect the sub frame to the vehicle,however the front of the engine is connected to the body by a rubber mount this keeps the engine at proper height absorbs vibration and hold engine in place.the trans axle is mounted to the sub frame with fluid filled rubber mounts.

Jan 20, 2010 | 2003 Chrysler PT Cruiser

1 Answer

2002 pontiac grand am rack and pinion replacement how to


Removing the rack and pinion assembly from a 2002 Pontiac Grand Am Se To get the old rack and pinion off of the car for replacement involves lowering the sub-frame, removing the stabilizer bar, and pulling the rack out from the driver side of the vehicle.
  • Start by lifting or jacking up the car and removing the front wheels. Once the car is safely supported, disconnect both tie rods from the steering knuckles.
  • The rear motor mount sits on top of the cross-member part of the sub-frame, and must be disconnected to allow the sub-frame to drop a few inches. Remove the three bolts attaching it to the center of the sub-frame - one in the back and two in the front near the back of the transmission.
  • Loosen the two bolts holding the front of the sub-frame. Place a scissor jack or bottle jack under the rear of the sub-frame where the bolt for the motor mount was. Remove the two smaller bolts from each side of the rear of the sub-frame (total 4 bolts) and then loosen the two remaining larger bolts holding the rear of the sub-frame (these bolts go through the rear control arm bushings and are very long) until the bolts are only going through the control arm bushing, and not into the chassis. You do not need to remove these completely.
  • Remove the stabilizer links from both sides.
  • Next you must disconnect the steering linkage. This is done easily by lifting up the rubber boot to expose the small bolt holding the linkage. Remove the bolt and pry the linkage upward using a pry tool or screw driver.
  • Near the passenger side of the crossmember, remove the bolt holding the power steering line bracket to the chassis. You may now begin to lower the sub-frame using the jack. The front bolts should have lowered the sub-frame about a half-inch or so, allowing you to lower the back of the sub-frame 3 or 4 inches.
  • With the sub-frame lowered, you can now access the bolts holding the stabilizer bar in place. The right side has a nut screwed onto the top of it holding the power steering lines, remove this first, then remove both bolts. Pry or pull the stabilizer brackets up and out. Remove the stabilizer bar.
  • Now you can get to both of the bolts holding the rack in place. Remove both of these, then begin to slide the rack toward the driver side wheel well until there is no more slack in the power steering lines. At this point you should be able to get to the nuts securing the lines on the rack. Loosen both nuts and be ready with something to cap the ends with. I used part of a plastic bag and a wire to tie it. You can now pull the rack out through the driver side.
  • Be sure to replace the rubber o-rings on the ends of the lines when putting the new rack in. Replace everything in the reverse order. Put your tie rods on the new rack, making sure to count the turns or make a mark or measure to be sure your tie rods end up close to the same length as before.
  • Bleed the power steering system.

Important: Get an alignment! Not only is it dangerous to drive with your steering out of align but it will also grate the tread off your tires in a matter of weeks or even days.

Oct 27, 2009 | 2002 Pontiac Grand Am

1 Answer

The parts are from canadian mustang the directions are lost. the are bolt on frame connectors for a 68 mustang coupe. can you help


I went on line and searched makers of theses I found COMPETITION ENGINIEERING on their site are instructions that complete for bolt in sub frame connectors for a 68 mustang. NOT JUST DRY FIT AND WELD IN !! They also have what could be uused as a guide for many other installs of parts to include the safety aspect of the job.

Oct 01, 2009 | Ford Mustang Cars & Trucks

1 Answer

Front Sway bar(Stabilizer bar)


please give good rating if this helps


Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal
  1. Raise vehicle on a hoist. Refer to Section 00-02 .
  1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Remove and discard nuts retaining stabilizer bar link (5K484) assembly to front stabilizer bar (5482) and front shock absorber (18124) with an 8 mm closed-end wrench and an 18 mm open-end wrench.


    ccf2026.gif

  1. Remove nuts retaining steering gear (3504) to front sub-frame, and move steering gear off the front sub-frame.
  1. With another set of support safety stands under front sub-frame, remove two rear subframe retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).




  1. Remove front stabilizer bar U-bracket bolts and replacestabilizer bar brackets and/or front stabilizer bar as required. Discard lower suspension arm stabilizer bar insulator (5493) and bolts.
Installation
  1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar insulator installation position.
  1. Lubricate inside diameter of new lower suspension arm stabilizer bar insulator with Rubber Suspension Insulator Lube E25Y-19553-A or equivalent meeting Ford specification ESF-M99B112-A. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber lower suspension arm stabilizer bar insulators.
  1. Install new lower suspension arm stabilizer bar insulators onto front stabilizer bar and position them in approximate location.
  1. Install stabilizer bar bracket on front sub-frames and install new bolts. Tighten to 30-40 Nm (22-29 lb-ft).
  1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Position steering gear onto front sub-frame and install retaining nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Install stabilizer bar link to front shock absorber and to front stabilizer bar, making sure that the stabilizer bar link is properly positioned. The letters "Top LH" and "Top RH" are moulded into the stabilizer bar link for correct assembly to the front shock absorber strut.
  1. Install new nuts and secure stabilizer bar link assembly to front stabilizer bar and front shock absorber. Tighten to 77-103 Nm (57-75 lb-ft) at front shock absorber strut and 47-63 Nm (35-46 lb-ft) at front stabilizer bar.
  1. Remove safety stands.
  1. Lower vehicle.

Apr 11, 2009 | 1995 Ford Taurus

1 Answer

Removing engine


Yes it does. The R&P is attached to the subframe of the car. When you undo the rear sub frame bolts be sure to have a jack under both sides of the sub frame to support. The R&P is bolted to the sub frame and so is the engine.

Sep 29, 2008 | 1999 Mercury Sable

Not finding what you are looking for?
1992 Chevrolet Lumina Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...