Question about Lincoln Continental

1 Answer

How difficult is it to remove the door lock cylinder from my 1994 Lincoln Contiental?

Posted by on

  • ratler333 Sep 26, 2009

    OK sounds simple, thanks.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Fairly easy. Remove all screws in door panel, pry out lock and window and mirror controls, then take a large flat-tip screw driver, pry panel off gently. THen pull up and off. Then you will see the lock and nut. Remove nut, and rod and remove lock cylinder.

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

Motor temp sensor on 97 Lincoln contiental


It is usually in one of the cylinder heads or somewhere near the thermostat housing. Look for a 1 or 2 wire connector with a brass nut below it.

Jun 25, 2014 | 1997 Lincoln Continental

1 Answer

How to replace blend door actuator on a 1997 lincoln contiental


The problem is most likely not just the blend door actuator, the electric motor actuators fais to move the door because the blend door warps and then it takes an excessive amount of power to move it or it will not move at all, which on this model is the case most of the time. The replacement of these parts requires the dash top be removed from the car, to do this job you need access to the factory service manuals. You can download them for a reasonable fee here. This is a 12-14 hour job at home for an amateur

Oct 30, 2012 | Lincoln Cars & Trucks

1 Answer

Back door will not open at all 1994 infiniti j30 how can i get it open tried to take off panel not enough room any solutions need help


Did you check to see if the child safety lock may have been activated? If so the door will only open from the outside.Try removing the power door lock switch/arm rest assembly to see if the door lock switch can be jumped out in the event the door lock switch is burnt out.
Does the Infiniti have an exterior key lock cylinder on the rear door? If so try to get a key to open the lock, it may be very difficult to remove the door panel when the door is sealed closed, but if you can that may be your only salvation short of attemting anslim jim door opening tool down the side of the door glass in ho[pes to trip the door linkage lock thus opening the door.

Jun 05, 2010 | 1997 Infiniti.5 J30

2 Answers

1994 Lincoln Contiental DCL warning light keeps coming on.


uve entered the computer universe-my condolences--today everyting is connected in almost an imposible logic-u have an OBD 1 system-before 96-go hav car scanned to obtain a data stream to translate the codes that may appear-repair manuals explain these

Sep 08, 2009 | 1990 Lincoln Continental

1 Answer

Car alarm


try unplugging the connector at the trunk lock cylinder

Jun 15, 2009 | 1998 Lincoln Continental

1 Answer

How do you replace the ignition switch on a 1994 Lincoln Town Car?


Here is how to remove ignition lock:

   Rotate ignition lock cylinder to RUN position. Using a 1/8-inch drift, depress lock cylinder retaining pin through access hole and remove lock cylinder.

Carefully NOTE: the position of the bearing retainer prior to removal.

   Remove blue plastic bearing retainer by inserting a screwdriver or similar tool, with a 90 degree bend on the tip, between bearing retainer and bearing and by prying upward.

   Insert tip of a screwdriver into Double-D slot of bearing, then rotate 90 degrees. Remove bearing.

   Remove lock drive gear. Carefully note relationship of lock drive gear to position of rack teeth.

Here is the installation:
   Position lock drive gear in base of lock cylinder housing in the same position as that noted during removal procedure. The position of lock drive gear is correct if last tooth on drive gear is meshed with last tooth on rack.

   Position bearing retainer in lock cylinder housing. Insert tip of a screwdriver into Double-D slot of bearing, then rotate 90 degrees.

   Press blue plastic bearing retainer into lock cylinder housing. Ensure retainer is in its original position.

   Line up flats of drive gear with flats of washer by pulling down on the column lock actuator.

   Install lock cylinder assembly.

   Check for proper start in PARK and NEUTRAL. Also, check to ensure start circuit cannot be actuated in DRIVE or REVERSE positions and the column is locked in LOCK position.

May 04, 2009 | 1994 Lincoln Town Car

1 Answer

My 1994 Lincoln Continental acts like it is out of gas when the gauge shows it still has some. First time, it said I had 3 gallons, second time 6 gallons, today it said I had 7 gallons left. When I put...


Hi Wayne the fuel pump needs replacing i have a 1994 contiental also what happens is that the digital gas bars on the insturment panel kept reading 2 bars then 3 bars not even going no where as i just turned the switch on and off i have different readings answer is to replace the fuel pump

Aug 02, 2008 | 2000 Lincoln Continental

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

fordexpert

Level 3 Expert

5530 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...