Question about 1992 Isuzu Rodeo

1 Answer

How do you take off a rotor on an 1992 Isuzu

How do you take off a front rotor on an 1992 Isuzu Rodeo 4x4?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 299 Answers

You need to remove the locking hub

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1992 izuzu rodeo LS 4x4 v6 and my brakes are having a hard time stopping i have replased the master cylinder the brake pads the rotors iv bled them but it still has a hard time stopping and it...


Check the caliper sliders, they may be seized causing limited brake pad contact. Also check the calipers for siezed pistons.
After bleeding the system, sometimes the proportioning valve will have to be reset manually. You can do this by having an assistant press the brake pedal and open a bleeder screw slightly on one side [ front or rear ] of the system, it may reset. If not, try doing the other side of the system.
If the brake pedal seems to be pushing back against you then either the Brake Booster isn't getting proper vacumn, or is faulty.
If the vehicle has drum rear brakes, make sure they are adjusted properly. If they are set too loose the pedal will feel spongy and low.
Hope this helps.

May 01, 2011 | 1992 Isuzu Rodeo

1 Answer

Need wiring diagram for 1992 Izuzu Rodeo 6 cyclinder.


For the 1992 Isuzu Rodeo 3.1L V6:
Firing Order
:

1-2-3-4-5-6
Cylinders:
.....(back)
5...............6
3...............4
1...............2
Distributor:
.....(back)
..............(+)-screw
.........4
..3
...................5
2
.................6
........1
(+)-screw
.....(front)
Rotation: Clockwise

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Aug 18, 2010 | 1992 Isuzu Rodeo

1 Answer

How do you take off front rotors on a 1992 isuzu trooper 4x4 auto


Just go to the Parts store and get repair manual less than $20.00 it will show you step by step how to. That's how I do my repairs on my cars over fifteen years now, up to replacing Timing Belt without a problem.

Mar 01, 2010 | 1992 Isuzu Trooper

1 Answer

Start truck up and a/t oil temp lt. blinking along with winter mode and power mode lt. blinks check transmision lgt stays on and brake and battery lt on and my volt meter shows no volts truck work fine...


I'm having the same problem. I have a 1992 Rodeo V-6 4x4. I replaced the alternator, battery, and even took out a killer stereo system in case of shorts (didn't have the patience to check). Except mine does start with a little boost. I'm thinking of replacing the battery for a bigger one, but not sure if that will take care of the problem. Help anyone?

Jul 31, 2008 | 1992 Isuzu Rodeo

1 Answer

92 Isuzu Rodeo Power loss


Do you have the v 6 or the 4 cyl.?
You may want to check the cap and rotor, and check to make sure all elctrical connections and vacuum hoses are tight and in good condition. Then go from there.

Jul 06, 2008 | 1992 Isuzu Rodeo

1 Answer

Isuzu Rodeo w/3.1L engine


Front Passenger side on cap is 1 - if you look on the inside of your cap there SHOULD be a pin marked with a 1, and the plugs go CLOCKWISE not counter. Just had the same problem myself with my 91 Rodeo. Cylinders are as follows Passenger side (front to back) 1 - 3 - 5, Driver side (front to back) 2 - 4 - 6. I called the Isuzu dealer and they told me it was counter clockwise, but when I hooked it up that way it backfired through the Carb.

Jul 05, 2008 | 1992 Isuzu Rodeo

1 Answer

1992 Isuzu Rodeo Distributor wires 3.1L engine


Hi,
Isuzu seem to have complicated things by changing engines, firing orders and even direction of rotation! As you can see, they've numbered the cylinders the other way than the 3.2L.

The Firing sequence for the 3.1 (traditional distributor) 6 cylinder is as follows -

d6e5b2a.jpg

If you take the distributor cap off, there should be a "No.1" formed on the inside. Stick a lead on this before you put the cap back on and go from there.
As leads are different lengths, you may have to swap a few to find the best fit.

I think 2 of them will look out of place - but that's the way it's designed. Just make use of clips for holding them neatly.

Thanks for using Fixya.









Jul 05, 2008 | 1992 Isuzu Rodeo

1 Answer

1992 Isuzu Rodeo Distributor wires


Hi,

On the 3.2L distriburorless ignition, the firing order is a straight 1-2-3-4-5-6.

Cylinder numbering .

88c39f7.jpg-

Hope this works for you

Jul 05, 2008 | 1992 Isuzu Rodeo

Not finding what you are looking for?
1992 Isuzu Rodeo Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...