Question about 2003 Buick Rendezvous

1 Answer

What are the torque specifications for front wheel bearings?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 299 Answers

If it is an axle nut it should be 150 ftlbs

Posted on Sep 25, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

  • 34 Answers

SOURCE: torque settings for wheel bearing

120Nm on all A3s with standard wheels.

Posted on Jan 22, 2009

  • 1 Answer

SOURCE: changing front wheel bearing

first take the wheel off
Then take the caliper off the rotor
Then take the rotor off the CV joint spindle
You will need to remove the three bolts that hold the bearing in place.
You will either need to remove the two bolts that hold the strut or
you will need a Puller.

Posted on Apr 01, 2009

  • 583 Answers

SOURCE: need torque setting for 1993 geo tracker front

i1m sorry to say that wheel bearings are not set to a torque specification, when you have repacked the bearings [ inner and outer ] ,reassembled it ,take the nut up until thewheel starts to drag and not turn very far when you try to spin it spin it backward and forward several times,grab the top of the wheel and try to push it in and out,if you getany movement at all tighten the nut a couple of castilations. do it all over again, spinthe wheel a few times and then try for the crossways movement again, if there is no movement ,you are very close to being right....................now comes the experience bit , iwould take it one more castilation of the nut because i know the feel that is need ed,,without that i suggest you put the pin in where you ereput the cap on and go for a 5 minute drive . whenyou get back ,jack it up and thespinning of the wheel again and try for the top crossways movement ,if there is any tighten thenut 2 castilations, and provided that when you try to spin the wheel by hand with a reasonably strong push the wheel should trael about 6 inches at least after your hand leaves it ,it is now a close as you are going to get itput it all to gether and for the next day or so put yor hand on the grease cap after you have driven anydistance, and you will feel it is warm but you should be able tohold your hand on the grease cap. there you have it ,any questions come back."youdoit"

Posted on Nov 06, 2009

germcelchar
  • 389 Answers

SOURCE: 1995 isuzu rodeo front wheel bearing torque specs.

To adjust wheel bearing torque. Tighten the nut fully until the wheel wont turn then unscrew slightly until the wheel turns freely. Replace the locking plate and its set.

Posted on Nov 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque setting for the front wheel bearing


There isn't a specific torque setting. You tighten the bearing nut while measuring axial play in the bearing. You want .01-.02mm of play in the bearing. A good rule of thumb is to tighten the nut with channel locks. Hold them backward so they don't pull tight on the nut as you turn. Turn not while holding pliers loosely until they slide off. Don't overtighten, you'll quickly trash the new bearings.

Feb 15, 2015 | Mercedes-Benz C-Class Cars & Trucks

3 Answers

Torque specifications 2000 chevy impala wheel bearing


The 2000 Chevroleticon1.png Impala is a sedan available in a pair of different versions, the base model and the LS. The Impala's torque specifications depend on the model, as the base and LS have different engines

Read more : http://www.ehow.com/list_7412083_2000-impala-torque-specifications.html

Oct 11, 2014 | 2000 Chevrolet Impala

1 Answer

Torque specs axle nut


Wheel nut torque 140 lb ft

Dec 31, 2013 | Cars & Trucks

1 Answer

What are mazda 6 wheel bearing torque specification


What is the front axle torque on a 2004 Mazda 6

Mar 17, 2012 | 2004 Mazda 6

1 Answer

REMOVAL OF FRONT WHEEL BEARINGS


Front (4 Wheel Drive) To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Tire and wheel assembly
    • Rotor (See: Disc Brake Rotor)
    • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
    • Electrical connection for the wheel speed sensor
    • Front drive halfshaft assembly (See: Halfshaft)
    • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

    • Hub and bearing assembly
To Install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
  2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
  3. Install or connect the following:
    • Hub and bearing assembly
    • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
    • Front drive halfshaft assembly (See: Halfshaft)
    • Electrical connection for the wheel speed sensor
    • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
    • Rotor (See: Disc Brake Rotor
    • Tire and wheel assembly
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  4. Torque the lug nuts to specification
  5. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 03, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

Front bearing nut torque specification rear wheel drive?


front bearing wheel nut holding axle on? 115 foot pounds and hammer in or crimp the nut after tightening. ^ like shape into slot of axle this locks the axle. for the wheel bearing for rear wheel drive the nut should be tightened by hand till tight 15 foot pounds then backed off 1/4 turn, be sure there is plenty of grees in the bearing cup before tighting nut be sure to line up slot for key with rotor on the rotor should turn free and should not have any slop in it, put the wheel on it and put the nuts on and try wiggleing the wheel back and forth if any movement readuast nut. If it is to tight it will over heat outter wheel bearing, also be sure there is greese in inner wheel bearing.

Jul 14, 2010 | 2000 Mercury Grand Marquis

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

Does the front wheel bearing hub assembly need to be torqued to specific tightness on a 2001 chevy venture?


if you mean the big nut in teh middle and its FWD then just pull it up tight with the snap on knuckle bar ,give it a **** or two and thats about the right torque.overtighten it and you WILL damage the bearing

Dec 13, 2009 | 2001 Chevrolet Venture

1 Answer

Torque specs for front spindle (nut hold brake drum in place)


Tighten till the wheel bearing is tight. No one really uses a specification for that, do it by feel. when the nut is tight, and there is no play in the bearing. Should be about 15-20 ft/lbs, with about .001-.003 end play if you need exact numbers though.

May 29, 2009 | 1965 Ford Mustang

Not finding what you are looking for?
2003 Buick Rendezvous Logo

463 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...