Question about 2004 Mazda 6

1 Answer

Reversing light failing to come on though new bulbs fitted

Posted by on

1 Answer

Two bulb don't fail together. Find a switch on the shifter mech or transmission which ever applies toyour vehicle

Posted on Sep 25, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How do you fit a drivers side indicator bulb on a 2001 renault kangoo ?

open the hood locate the rear of the indicator , the bulb holder will turn anticlockwise about a quarter turn then will come out , fit the new bulb , push and twist , reverse for refitting, job done

May 05, 2014 | 2003 Renault Kangoo

1 Answer

Turn signal

it would be the bulb fitting. they can go weak or discoloured and not contacted the bulb fitting. take the bulb out and clean the fitting. failing that check the plug to the light fitting it can get a covering of oxidised coating on them breaking the circuit.

Sep 12, 2013 | 2001 Chrysler Town & Country

1 Answer

How to replace bulb in front bumper turn signal housing 1995 jag xj6

  • Identify the blown bulb. Note that if a headlight bulb has blown, the dip beam is on the outside and the high beam is on the inside. Turn off the ignition switch and light switches.

  • Open the hood and replace any blown headlight bulbs. Press the plastic spring clips and remove the bulb holder from the assembly. Pull the bulb out of the bulb holder and replace it with a new bulb. It only fits one way. Be sure not to touch the bulb's glass. Replace any parking lights at the same time, they are in the headlamp unit too.

  • Remove the front turn signal light unit in the bumper to change the turn signal bulb. Push gently on the inside edge and insert a blade between the bumper and the lens at the outside edge. Compress the spring and remove the lens. Fit a new lamp by inserting it into the plug. The side marker light is changed using a similar process.

  • Open the trunk to replace the rear fog light, stop light, tail light, reversing light and turn signal light. Remove the rear light cover and turn the bulb holder fastener 90 degrees counter clockwise. Remove the expired bulb, fit a new one and replace the parts, turning the bulb holder clockwise.

  • Thanks..

    May 21, 2011 | 1995 Jaguar XJ6

    1 Answer

    For 3 days the passenger brake light has not worked but the bulb is still good, and now the opposite reverse light is not working, what is the problem?

    2 seperate circuits even though the bulbs look good sometimes when the elements get hot they expand and dont make contact i would try some new bulbs a handful of bulbs are cheaper than a tail light indicator sensor and check the ground scews when installing the bulbs good luck let me know by rating this info

    Mar 07, 2011 | Toyota Tacoma Cars & Trucks

    1 Answer

    How do I change a brake light bulb in a 1999 c70 volvo?

    Welcome to
    Brake Lamp Replacement

    Location of the lights


    The illustration shows the locations of the lights on the RH side. The LH side is the same but


    The lights have the following functions:

    - 1 +1 = Parking light Fail light

    - 2 = Reversing light

    - 3 = Fog light LH side only (LHD cars)

    - 5 = Direction indicator

    - 6 = Brake light


    Tail light changing bulbs

    Ignition off.

    Open the cover in front of the tail light

    Undo the wing nut and take out the lamp holder.

    Change the defective bulb.

    Fit in reverse order.

    Check that all bulbs lamps are intact and in working order.


    Replacement of tail light cluster

    Note! If a new tail light is to be fitted, the sleeves must be ground down 1.5 mm.

    Open the cover in front of the tail light Undo the panel partly in front of the tail light Unplug the

    connector for the tail light Undo the four nuts securing the tail light see illustration.

    Pull the tail light straight out. Fit in reverse order

    Note! check the sealing and fit on reassembly.

    Check that all bulbs lamps are intact and in working order.Thank you for Using FixYa.comKind Regards, LeeYour FixYa Expert and Master Technician

    Jan 27, 2011 | 1999 Volvo C70

    1 Answer

    I want to replace the entire headlight assembly on the drivers side of a 2006 Chevy Cobalt. How do I do that?

    on most of the new cars the head light assembly comes out pretty quick and easy. on top of the assebly there is typicaly two pins. there are eather steal or plastic. you have to pull these pin up and out of the back of the assebly. steal pins come all the way out, but plastic typical come only part of the way out. the assembly will then pull strait out, but can be a tight fit sometimes. unplug light bulbs and reverse procedure with new headlight assembly
    be carefull not to touch the glass on the bulbs with you fingers. the oil from your skin will cause the bulbs to fail prematurely.

    Apr 24, 2010 | 2006 Chevrolet Cobalt

    1 Answer

    How to change the bulb on the front head light on my 2002 jaguar x-type

    Dip beam (outer) headlight
    Open the bonnet.
    Slide open the two spring clips (A) and remove the cover (B).
    Press the spring clip inwards and push towards the bulb
    to release the bulb and then remove the bulb from the light
    unit. Pull the connector from the bulb.
    Fit a new bulb to the connector, type H1 for dipped beam.
    Fit the bulb to the light unit, the bulb will only correctly fit in
    one position. Engage the spring clips to retain the bulb and then
    fit the cover and retain using the two spring clips.
    Close the bonnet.
    Note: High Intensity Discharge (HID) Xenon light units,
    type D2S 35W, are not renewable, contact your Dealer if the headligh fails to operate

    Oct 07, 2009 | 2002 Jaguar X-Type

    2 Answers


    connect a new light on to the same circuit as the reversing light, take the postive off the reversing light, the earth goes to ground on the new light

    Aug 10, 2009 | 2009 Toyota Land Cruiser

    1 Answer

    Brake light wiring reversed?

    hi go back to bulb and make sure the bulb you have fitted is for indicator? this has only one element and has only one centre contact for power also check the side pins on the body of bulb they should be opposite one another and on same level as you look on side however here in uk some of these bulbs are the same as above but for the locating pins as described above the pins are on same level but not opposite each other so if you try fitting should not be able to fit easily bayonet suggest you check the other side rear light bulbs one at atime to ensure correct type are what you have fitted stop and tail light bulbs have two elements one for brake and one for tail light these locating pins are oposite each other but not on same level offset to ensure the elements are on correct circuit when fitted hope you understand ?

    Nov 02, 2008 | 1995 Ford Contour

    Not finding what you are looking for?
    2004 Mazda 6 Logo

    40 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts


    Level 3 Expert

    75824 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8215 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides