Question about 1995 Isuzu Trooper

Open Question

I need to replace the front main seal on a isuzu 95 pu 2.3 Ltr.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace waterpump on Isuzu trooper with a 5.0


these are easy take the belts and fan shroud off and fan off take off the water pump save your anti freeze pu a pan under the area of the pump on the ground as to not make a mess , remove the 4 bolts that hold it on watch the seal or gasket , you have to replace that but make sure you get it off all unless it is a seal ring type but change it also , if it is a ring gasket put a little oil or something so it goes into the hole easy put it back together , look on youtube , should be there they are pretty easy

Dec 19, 2014 | 2001 Isuzu Trooper

1 Answer

2.5 ltr 1998 boxter front crank seal noisy


Are you sure its the seal squealing? - very unusual, check belts and v drives.

Feb 15, 2014 | 1998 Porsche Boxster

2 Answers

Need to replace the harmonic balancer in a 1994 isuzu rodeo. ( rwd, 3.2 ltr v.6 ). no success so far. is the main bolt reverse threaded? so far i have been attempting to turn it toward the passenger side,...


No, the bolt is not left handed. You do need to turn it counter-clockwise to loosen it. You're probably just spinning the engine when trying to loosen it. I use a 6" c-clamp and attach it behind the balancer in a way that the threaded shaft can lodge up against something so the engine can't turn. Then I use a 3 lb rubber mallet and hit the 1/2" drive rachet on the handle, or put a breaker bar on the end of it and work it loose that way. Once you get the bolt off, you will need to use a pulley puller to get the balancer off.

Mar 19, 2011 | Isuzu Rodeo Cars & Trucks

2 Answers

Need a engine diagram for a 2.8 ltr v6 showing rear main seal


Just a little advise before you jump to thinking the rear main seal is leaking. The vast majority of the oil leaks from these 2.8L motors are the rear intake manifold seal and the distributor o-ring. I would check them first. The rear main seal is in the lower rear of the motor, you have to remove the transmission to replace ti.

Jan 22, 2011 | Pontiac Firebird Cars & Trucks

1 Answer

How to replace front crankshaft seal on 1987 Nissan PU, 4 cyl. 4X4. D21


When I did mine I removed the belts, removed the harmonic Balancer and used a seal puller to pull the seal out and then pressed the new seal in.

Jul 23, 2010 | 1987 Nissan Pickup

2 Answers

Fuel injector problem


Sounds like either incorrect installiation or defective seals/O rings. May be wise to recommend to the repair shop to use dealer parts if they are not using them.

May 18, 2010 | 1989 Isuzu Pickup 2WD

1 Answer

95 gmc sierra k1500 4x4 5spd manual noise


the leak is probably a separate issue from the noise. is the leak very bad? can you tell if it's engine oil or transmission lube/fluid? most likely the rear main bearing seal needs replacing. the noise is most likely the clutch release bearing. you should replace all components of the clutch assembly which include; clutch plate, pressure plate, release bearing and piolot bearing. also have the fly wheel resurfaced. while the trans is out, you can check the rear main seal and the trans input shaft seal and replace accordingly.

May 03, 2010 | 1993 GMC Sierra K1500

1 Answer

I need to find the timing (TDC) marks for my 95 isuzu rodeo. I had to replace the front main seal gasket. I had to pull the harmonic balancer to get to the seal. I put everything back together & now...


There is no way that could happen unless you did not put the woodruff key back into the crankshaft recess and put crank pulley on random!!!

Apr 11, 2010 | 1995 Isuzu Rodeo

1 Answer

I need to replace the bulb on my 95 rodeo front blinker. It has a couple of screws, but I took them out and for the life of me I can't get the lens cover off?


The len's is a sealed unit you need to remove the light. The light is held in with the screws you have taken out but also has a plastic round holder on the back which connects it to the pannel (wheel arch) . To remove the light pull it straight out from the front. Sometimes they can not be removed by hand so you may need to pry it slightly with a screwdriver between the lens and the wheel arch. Be carefull not to damage the paint.

Jan 14, 2010 | 1995 Isuzu Rodeo

1 Answer

'94 Isuzu pu (carb.) Sometimes dies while running down freeway


Check all the old ' brittle plastic vacume line connections .And the idle control valve unit located near the passenger side firewall. Over the front wheel cover. passenger side.over.

Feb 12, 2009 | 1993 Isuzu Pickup

Not finding what you are looking for?
1995 Isuzu Trooper Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...