Question about Volkswagen Golf

1 Answer

I have bled brakes replaced front pads and even replaced rear passager wheel cylinder and re bled brakes still not working when car is running

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Did you run out of brake fluid , if you did the brake master cylinder seal may have reversed and when you are trying to bleed the brakes the fluid is bypassing the seal , you think you have a good pedal when the engine is not running , but when you start the engine the pedal goes to the floor , you will need to fit a new or second hand master cylinder to cure the problem , I had this with my sons car and the problem was cured with a second hand master cylinder , I hope this helps

Posted on Mar 08, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Soft pedal on 03 grand caravan


Have you driven it since the brakes where replaced?

Did you bleed all four wheels?

have you "broken in" the new pads?

Are the rears drum or disk? If drum are they adjusted correctly?

are you using remanufactured master cylinders? If so keep replacing them. eventually you will get one that works. New is pricey but a better way to go.

Jan 22, 2013 | Cars & Trucks

1 Answer

I replaced disc brake pads, rear shoes. wheel cylinder,master cylinder, power brake booster all new. Question: My brake pedal is not solid,goes low to the floor almost. I have bled the master cylinder 1st,...


Check your lines going to the brakes the rubber hose on the 1993 chevy have a tendancy to crack and brake are you using an excess of brake fluid

Sep 12, 2011 | 1993 Chevrolet C1500

1 Answer

I have changed the rear rotors and brake pads, bled the brakes after putting itall back together. Seemed to have brakes but then shortly thereafter they are like a sponge. Last time I tried bleeding them...


Hi, bleeding your rear brakes with engine running, you should get enough pressure out of the lines to squirt 3-4 feet. In other words, good pressure. If all you get is a trickle, you probably have a bad master cylinder. Just because its full of fluid, does not mean the seals arent shot. If you have bled them in order, left rear,right rear,left front,right fornt and have bled them enough to get fresh fluid out of each one without achieving good solid pressure at all wheels, replace your master cylinder. There is a proportioning valve, but usually it will affect only one wheel when going out, usually the left rear.
Brake pedal height comes from the rear brakes, so if you have bad pressure there, you will never get a good pedal. Eventually with a bad master, your brakes will go completly out..Mike

Jun 20, 2011 | 2001 Dodge Ram 2500 Truck

1 Answer

Replaced front calipers,master cylinder,front and rear pads and resurfaced all four rotors.I bled the brakes starting with right rear then left rear, right front then left front and still feels like there...


did you bench bled master? if yes do you have abs system,if so you must bleed at abs block,if it has bleeders, if not then you must line bleed all 6 lines.2in from master 4 out to wheeles. then rebleed wheel in cylinder.If you have bleeders at abs block you dont to rebleed wheels. best dun with powerbleeder. hoooooops this helps

Jun 12, 2010 | 2000 Mercury Grand Marquis

2 Answers

I have re/re the rear brake cylinders,shoes,drums,front rotors,pads,and callipers on my 2000 gmc safari van.i have bled all the brakes. but the drivers front has no pressure or fluid.the other three brakes...


make sure you are bleeding them by doing them as an abs system,do the right rear then the left front,then the left rear then the right front,the opposite wheels are how the system brakes.

Jan 21, 2010 | 2000 GMC Safari

2 Answers

Brake pedal goes to floor,replaced front pads rear good,bleed brakes no help


Hi:
If you have replaced all pads, and see no leaks at any wheel, and have bled your brake system, then most likely your brake master cylinder has failed.

Dec 18, 2009 | 2001 Ford Taurus

2 Answers

1989 Ford F350 2 wheel drive dually 460 ci gas motor


5 Inspect Brake Fluid Type Brake fluid loss or contamination grey_line.gif 10 Inspect Master Cylinder (Brake System) Worn or leaking brake master cylinder. grey_line.gif 11 Inspect Brake Power Booster Damaged booster vacuum line/check valve, or diaphram

Nov 24, 2008 | 1989 Ford F 350

1 Answer

1999 plymouth voyager brakes


the master cylinder needs to be "bench-bled" before installation, if you are doing this and still having the problem, did you look into changing the rear brakes as well? check rear wheel cylinders for any small leaks

Jul 16, 2008 | 1999 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...