Question about 2000 Jeep Cherokee

1 Answer

How do you bleed an aftermarket slave cylinder on a 2000 jeep wrangler

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Regardless of if it's aftermarket or factory they all have a bleed screw. Open the screw and have someone push down on the clutch. close the screw when pedal is still all the way down. Repeat "till no air comes out of screw. During the process don't permit the master to run dry or you will have start all over again.

Posted on Sep 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 jeep wrangler clutch has to pressure and thus wont allow me to put it in gear.


Check the clutch fluid level. If it's low, add some (takes brake fluid). There is a bleed valve down on the clutch slave cylinder on the bellhousing. Open the bleed valve and have someone push the clutch pedal slowly to floor, and hold. Close the bleed valve, and repeat until fluid comes out in a steady stream when the pedal is depressed. Your pedal should have pressure now, and the clutch should be working.
If no fluid is forced out the clutch master cylinder, into the line, and to the slave cylinder when clutch is pressed, then you may have a bad clutch master cylinder. If fluid does come out the bleed valve, but still no pressure on the pedal, it may be a bad slave cylinder.
Post back for more. Would like to know what you find out, and what the problem was, OB. Good luck.

Jul 13, 2012 | 1991 Jeep Wrangler

1 Answer

Where do you bleed the clutch at on a 1997 jeep wrangler what is the location of it


This all depends if this is a hydraulic clutch or if its cable operated, you can only bleed hydraulic clutches, to bleed it you would bleed at the ******, you will see the bleeder screw on the slave cylinder that operates the clutch fork.

Sep 03, 2011 | 1991 Jeep Wrangler

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

2 Answers

Where do you bleed the hydralic clutch on 1998 Jeep Wrangler 6 cyl.


you can do this at the slave cylinder down at the transmission make sure the resvoir is full and bleed like you would brakes

Jan 02, 2010 | 1998 Jeep Wrangler

1 Answer

My 2001 jeep wrangler has no bleeder on the slave cylinder how do you bleed this thing just gravity?


Hi, the master and slave come prebled from factory so unfortunatly you will have to buy a new one

Nov 09, 2009 | 2001 Jeep Wrangler

2 Answers

I need to bleed the clutch on my 1992 jeep wrangler and need to know were to locate the bleeder insert


The bleeder valve will be on the slave cylinder. Follow the hydraulic line from the Master Clutch cylinder down to the slave cylinder by the transmission.

Oct 04, 2009 | 1992 Jeep Wrangler

1 Answer

How do you bleed the clutch in a 1991 Jeep Wrangler?


If replacing just the fluid, you should gravity bleed it by opening the valve at the side of the transmission where the line goes in to connect with the slave cylinder. Be sure to stand by and keep the tiny reservoir from going empty during bleeding, or you just make things worse. Assume you replaced parts. Is this right or wrong?

Or are you just trying to restore performance in a poorly operating system? Would help TONS to know these details, and how much you know about bleeding, etc. If you are trying to bleed a new slave cylinder, it can take 600 to 1800 pumps of the clutch pedal sometimes to clear it out manually. If you want instructions on how to bleed in with vacuum assistance, please post request comment to that effect.

Talk to you soon. TT

Feb 06, 2009 | 1991 Jeep Wrangler

1 Answer

1994 Jeep Wrangler 4cyl - Bleeding slave cylinder


This is not a bleeder hole, this is a weep hole like in a water pump to see when there is seepage past the seals.

Bench bleed the system. With the master cyl. line and slave cyl assembled, place the master cylinder in a vise, fill the master cyllinder. actuate the slave cylinder back and forth lower than the master cyl. This will allow the air to escape upwards back into and out of the master cyl.
Once bled the system can be installed.

Good Luck

Aug 06, 2008 | 1994 Jeep Wrangler

1 Answer

Where is a bleed screw for a 2000 6cyl for the clutch,its not where the book said it would be


it is on the slave cylinder on the back of the bellhousing it is an inset hexhead screw. it takes like a 4mm hex key.

Jul 24, 2008 | 2000 Jeep Wrangler

1 Answer

Wrangler 2000 clutch


the slave cylinder needs to be level. get a small bubble level and jack up the front or rear appropriately till its level.

May 24, 2008 | 2000 Jeep Wrangler

Not finding what you are looking for?
2000 Jeep Cherokee Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...