Question about 1994 Toyota Camry

Open Question

How do i get the left side axel out - 1994 Toyota Camry

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pulled out axels to check an now they won't go back in


front or rear axels and did you have the left and right side out at the same time.

Nov 23, 2014 | 2001 Jeep Grand Cherokee

1 Answer

1998 GMC Sierra K2500 Wont go in to 4X4


Switch has high failure rate. If that's the one mounted on the left side of the instrument panel.

Mar 17, 2013 | Cars & Trucks

1 Answer

How do I remove the front left axle shaft on a chevy 2007


remove the axle nut first, always took the upper ball joint loose just take the nut off apply some upwards pressure and hit spindle with hammer and it will allow you to move the hub and all out enough to remove axle. the upper ball joint nut has to come off
and seperate the ball joint from the steering knuckle
then plenty of room. good-day ! then just slide axel out,or pry between axel and ****** to pop it loose, it has a locking clip on transmission side. when putting back in make sure axel is locked in ******. and do not forget to torque axel nut when done.

Aug 05, 2011 | 2000 Chevrolet Silverado

1 Answer

My 1994 toyota camry lex left axel cv bost is repture, my mechanic suggesting me to replace the left axel instead just do the cv bost. Any suggestion?


if the cv joint boot cover is bad then you might have got dirt or road dust in there.
I would replace the half shaft or left axle would only cost a little more for new axle.
and be safer.
also check the right side it might be do also.
can do one at a time because of money.

Feb 22, 2011 | 1994 Toyota Camry

1 Answer

I'am trying to take the transaxle out of the transmission to fix an oil leak


Remove the wheel cover and loosen the drive axel hub nut. loosen the the wheel lug nuts raise the vehicle and support it well. NOTE: you will have to be working under the car be very careful. remove the drive axel hub nut. To prevent the hub from turning, insert a screwdriver thru the brake caliper and into one of the cooling slots on the rotor. remove the control arm-to-steering knuckle. Check for the ABS sensor and remove it out of your way. Separate the drive axel from the hub. If stuck remove the brake caliper and rotor. Push the axel out of the hub with a puller or you can use a good solid broom handle and drive it out. If you are removing the right side axel you will need a slide hammer and adaptor to separate the axel from the trans. If you are removing the left side, carefully pry the axel out of the trans. with a large pry-bar positioned between the inner CV joint and the trans. case. Use the subframe as a pivot point. Hold the CV joints so they do not separate inside the rubber if going to reuse them. Lubricate the new seal with multi-purpose grease before you install it.

May 05, 2010 | 2001 Chevrolet Impala

1 Answer

Where is the actuator switch located on the transfer case?(the switch that engages the 4wd)Thanks!


The actuator solenoid along with the axel solenoid
switch are located at the rear of the front axel on the
right side.And the transfer case switch is located on
top of the transfer case left side. Hope this helps.

Feb 08, 2010 | 1993 Chevrolet K1500

1 Answer

The rear axel leaks on the left side. Had the


get a roller/seal bearen replacement bearen seal 70 to 100 $ but it will work its 3 inch long by how big the hole is

Jan 27, 2010 | Chevrolet Tracker Cars & Trucks

2 Answers

2001 and 2002 jeep grand cherokee. while making hard left hand turn experience rumbling sound doesnt happen when driving straight or right turns. Cant decide if sound is from front or rear area


Try checking the bearing in the left wheel if the rumbling is on the left side. Sometimes bearings can be worn down and sometimes may even twist or bend.

Aug 21, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Hi, can you tell me how I can remove left side drieaxel of my 1992 Toyota celica GT I already remove the whole wheel hub assembly away from the car


usually just pry between tranny and axel and pops off. see this has a c clip on the end off the axel so it has some pressure.just pry and it should pop right off. ps make sure theres no pin on the axel if there is just use a center punch and push it out you might need a hammer.

Jun 29, 2009 | 1992 Toyota Celica

1 Answer

1995 maxda protege left side axel removal


I HAVE MADE A TOOL TO REMOVE THE AXLE SHAFT FROM THE RIGHT SIDE FROM A PIECE OF ROUND STOCK ALL YOU HAVE TO DO IS GRIND A U SHAPE ABOUT 2" DEEP TO FIT AROUND THE DIFF PIN INSIDE AND KNOCK IT OUT

May 07, 2009 | 1995 Mazda Protege

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...